config: Ender 3 S1/S1 Pro Default Configurations (#5332)

Signed-off-by: Rob Casper <myallneedsemail@gmail.com>

1 files changed, 132 insertions, 0 deletions

diff --git a/config/printer-creality-ender3-s1-2021.cfg b/config/printer-creality-ender3-s1-2021.cfg
new file mode 100644
index 00000000..ab799e19
--- /dev/null
+++ b/config/printer-creality-ender3-s1-2021.cfg
@@ -0,0 +1,132 @@
+# This file contains pin mappings for the stock 2021 Creality Ender 3
+# S1. To use this config, check the STM32 Chip on the V2.4S1 Board
+# then during "make menuconfig" select either the STM32F103 with a
+# "28KiB bootloader" or select the STM32F401 with a "64KiB bootloader"
+# and serial (on USB PA10/PA9) communication for both depending on the
+# STM32 Chip installed on your printers Motherboard.
+
+# If you prefer a direct serial connection, in "make menuconfig"
+# select "Enable extra low-level configuration options" and select
+# serial (on USB PA10/PA9), which is broken out on the 10 pin IDC
+# cable used for the LCD module as follows:
+# 3: Tx, 4: Rx, 9: GND, 10: VCC
+
+# Flash this firmware by copying "out/klipper.bin" to a SD card and
+# turning on the printer with the card inserted. The firmware
+# filename must changed to "firmware.bin"
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PC2
+dir_pin: PB9
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA5
+position_endstop: -10
+position_max: 235
+position_min: -15
+homing_speed: 50
+
+[stepper_y]
+step_pin: PB8
+dir_pin: PB7
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA6
+position_endstop: -10
+position_max: 241
+position_min: -15
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 8
+endstop_pin: probe:z_virtual_endstop
+position_max: 270
+position_min: -4
+
+[extruder]
+step_pin: PB4
+dir_pin: PB3
+enable_pin: !PC3
+microsteps: 16
+gear_ratio: 3.5:1
+rotation_distance: 26.3585
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+control: pid
+pid_Kp: 23.561
+pid_Ki: 1.208
+pid_Kd: 114.859
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: PA7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_Kp: 71.867
+pid_Ki: 1.536
+pid_Kd: 840.843
+min_temp: 0
+max_temp: 110
+
+[heater_fan hotend_fan]
+pin: PC0
+heater: extruder
+heater_temp: 50.0
+
+[fan]
+pin: PA0
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 2000
+max_z_velocity: 5
+max_z_accel: 100
+
+[bltouch]
+sensor_pin: ^PC14
+control_pin: PC13
+x_offset: -31.8
+y_offset: -40.5
+z_offset: 0
+probe_with_touch_mode: true
+stow_on_each_sample: false
+
+[bed_mesh]
+speed: 120
+mesh_min: 20, 20
+mesh_max: 200, 200
+probe_count: 4,4
+algorithm: bicubic
+
+[safe_z_home]
+home_xy_position: 147, 154
+speed: 75
+z_hop: 5
+z_hop_speed: 5
+move_to_previous: true
+
+[filament_switch_sensor e0_sensor]
+switch_pin: !PC15
+pause_on_runout: true
+runout_gcode: PAUSE
+
+[pause_resume]
+recover_velocity: 25