config: Add BigTreeTech EBB V1.2 / EBB SB V1.0 / E3EZ / M5P / M8P V1.1 / Octopus Max EZ

Signed-off-by: Alan.Ma from BigTreeTech tech@biqu3d.com
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

1 files changed, 199 insertions, 0 deletions

diff --git a/config/generic-bigtreetech-manta-m5p.cfg b/config/generic-bigtreetech-manta-m5p.cfg
new file mode 100644
index 00000000..b41a0cd6
--- /dev/null
+++ b/config/generic-bigtreetech-manta-m5p.cfg
@@ -0,0 +1,199 @@
+# This file contains common pin mappings for the BIGTREETECH Manta M5P
+# To use this config, the firmware should be compiled for the
+# STM32G0B1 with a "8KiB bootloader" "8 MHz crystal"
+# and "USB (on PA11/PA12)" or "CAN bus (on PD0/PD1)".
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PC8
+dir_pin: !PC9
+enable_pin: !PA15
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PD3
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_y]
+step_pin: PA10
+dir_pin: !PA14
+enable_pin: !PA13
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PD2
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_z]
+step_pin: PC6
+dir_pin: PC7
+enable_pin: !PA9
+microsteps: 16
+rotation_distance: 8
+endstop_pin: ^PC3
+position_endstop: 0.0
+position_max: 200
+
+[extruder]
+step_pin: PB12
+dir_pin: !PB11
+enable_pin: !PA8
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PC5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PA1
+control: pid
+pid_Kp: 21.527
+pid_Ki: 1.063
+pid_Kd: 108.982
+min_temp: 0
+max_temp: 250
+
+#sensor_type:MAX31865
+#sensor_pin: PA4
+#spi_bus: spi1
+#rtd_nominal_r: 100
+#rtd_reference_r: 430
+#rtd_num_of_wires: 2
+
+#[filament_switch_sensor material_0]
+#switch_pin: PC2
+
+#[extruder1]
+#step_pin: PB0
+#dir_pin: PB1
+#enable_pin: !PC4
+#heater_pin: PA7
+#sensor_pin: PA2
+#...
+
+[heater_bed]
+heater_pin: PA5
+sensor_type: Generic 3950
+sensor_pin: PA0
+control: watermark
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PA4
+
+#[heater_fan fan1]
+#pin: PA3
+
+#[heater_fan SoC_fan]
+#pin: CB1: gpio79
+#pin: RPI: gpio26
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+########################################
+# TMC2209 configuration
+########################################
+
+#[tmc2209 stepper_x]
+#uart_pin: PD9
+#run_current: 0.800
+#diag_pin: PD3
+
+#[tmc2209 stepper_y]
+#uart_pin: PD8
+#run_current: 0.800
+#diag_pin: PD2
+
+#[tmc2209 stepper_z]
+#uart_pin: PB10
+#run_current: 0.800
+#diag_pin: PC3
+
+#[tmc2209 extruder]
+#uart_pin: PB2
+#run_current: 0.600
+#diag_pin: PC2
+
+#[tmc2209 extruder1]
+#uart_pin: PA6
+#run_current: 0.600
+#diag_pin:
+
+########################################
+# TMC2130 configuration
+########################################
+
+#[tmc2130 stepper_x]
+#cs_pin: PD9
+#spi_bus: spi2
+#run_current: 0.800
+#stealthchop_threshold: 999999
+#diag1_pin: PD3
+
+#[tmc2130 stepper_y]
+#cs_pin: PD8
+#spi_bus: spi2
+#run_current: 0.800
+#stealthchop_threshold: 999999
+#diag1_pin: PD2
+
+#[tmc2130 stepper_z]
+#cs_pin: PB10
+#spi_bus: spi2
+#run_current: 0.650
+#stealthchop_threshold: 999999
+#diag1_pin: PC3
+
+#[tmc2130 extruder]
+#cs_pin: PB2
+#spi_bus: spi2
+#run_current: 0.800
+#stealthchop_threshold: 999999
+#diag1_pin: PC2
+
+#[tmc2130 extruder1]
+#cs_pin: PA6
+#spi_bus: spi2
+#run_current: 0.800
+#stealthchop_threshold: 999999
+#diag1_pin:
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=PD5, EXP1_3=PB3, EXP1_5=PB5, EXP1_7=PB7, EXP1_9=<GND>,
+    EXP1_2=PD4,  EXP1_4=PD6, EXP1_6=PB4, EXP1_8=PB6, EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=PB14, EXP2_3=PB8, EXP2_5=PC10, EXP2_7=PC12,  EXP2_9=<GND>,
+    EXP2_2=PB13, EXP2_4=PB9, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>
+
+# See the sample-lcd.cfg file for definitions of common LCD displays.
+
+#[bltouch]
+#sensor_pin: PC13
+#control_pin: PC15
+
+# Proximity switch
+#[probe]
+#pin: PC15
+
+#[neopixel my_neopixel1]
+#pin: PC11
+
+#[neopixel my_neopixel2]
+#pin: PC14
+
+#[adxl345]
+#cs_pin: PC0
+#spi_bus: spi2