diff options
| author | Kevin O'Connor <kevin@koconnor.net> | 2017-05-21 11:47:09 -0400 |
|---|---|---|
| committer | Kevin O'Connor <kevin@koconnor.net> | 2017-05-21 11:51:58 -0400 |
| commit | 944c121a00366dffc87643fbcf93df0aef5e1889 (patch) | |
| tree | 137f1227b3840985098d27ac41d919443d02aa76 /config/example.cfg | |
| parent | c9b66621381fda9d3af02253ca30c0119b62d7b2 (diff) | |
| download | kutter-944c121a00366dffc87643fbcf93df0aef5e1889.tar.gz kutter-944c121a00366dffc87643fbcf93df0aef5e1889.tar.xz kutter-944c121a00366dffc87643fbcf93df0aef5e1889.zip | |
config: Add periods to end of sentences in example configs
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Diffstat (limited to 'config/example.cfg')
| -rw-r--r-- | config/example.cfg | 16 |
1 files changed, 8 insertions, 8 deletions
diff --git a/config/example.cfg b/config/example.cfg index 08a778c9..45508f9f 100644 --- a/config/example.cfg +++ b/config/example.cfg @@ -18,7 +18,7 @@ # The stepper_x section is used to describe the stepper controlling -# the X axis in a cartesian robot +# the X axis in a cartesian robot. [stepper_x] step_pin: ar29 # Step GPIO pin (triggered high). This parameter must be provided. @@ -77,7 +77,7 @@ position_max: 200 # The stepper_y section is used to describe the stepper controlling # the Y axis in a cartesian robot. It has the same settings as the -# stepper_x section +# stepper_x section. [stepper_y] step_pin: ar27 dir_pin: ar26 @@ -90,7 +90,7 @@ position_max: 200 # The stepper_z section is used to describe the stepper controlling # the Z axis in a cartesian robot. It has the same settings as the -# stepper_x section +# stepper_x section. [stepper_z] step_pin: ar23 dir_pin: !ar22 @@ -105,7 +105,7 @@ position_max: 200 # controlling the printer extruder and the heater parameters for the # nozzle. The stepper configuration has the same settings as the # stepper_x section and the heater configuration has the same settings -# as the heater_bed section +# as the heater_bed section (described below). [extruder] step_pin: ar19 dir_pin: ar18 @@ -151,7 +151,7 @@ filament_diameter: 3.500 # buildup. This setting only applies if pressure_advance is # non-zero. The default is 0.010 (10 milliseconds). # -# The remaining variables describe the extruder heater +# The remaining variables describe the extruder heater. heater_pin: ar4 # PWM output pin controlling the heater. This parameter must be # provided. @@ -219,7 +219,7 @@ control: watermark min_temp: 0 max_temp: 110 -# Extruder print fan (omit section if fan not present) +# Extruder print fan (omit section if fan not present). [fan] pin: ar14 # PWM output pin controlling the fan. This parameter must be @@ -234,7 +234,7 @@ pin: ar14 # Time (in seconds) to run the fan at full speed when first enabling # it (helps get the fan spinning). The default is 0.100 seconds. -# Micro-controller information +# Micro-controller information. [mcu] serial: /dev/ttyACM0 # The serial port to connect to the MCU. The default is /dev/ttyS0 @@ -260,7 +260,7 @@ custom: # LEDs, to configure micro-stepping pins, to configure a digipot, # etc. -# The printer section controls high level printer settings +# The printer section controls high level printer settings. [printer] kinematics: cartesian # This option must be "cartesian" for cartesian printers. |