diff options
| author | Kevin O'Connor <kevin@koconnor.net> | 2018-08-03 13:00:40 -0400 |
|---|---|---|
| committer | Kevin O'Connor <kevin@koconnor.net> | 2018-08-03 13:00:40 -0400 |
| commit | 43179d7b6c7c90d24021367b05fda94ca4442036 (patch) | |
| tree | 7014cbe8c3c931f13ac114a2ac1821652ba11b0d /config/example-extras.cfg | |
| parent | 82738955d2b99c5e91a84affff658ca978e058ec (diff) | |
| download | kutter-43179d7b6c7c90d24021367b05fda94ca4442036.tar.gz kutter-43179d7b6c7c90d24021367b05fda94ca4442036.tar.xz kutter-43179d7b6c7c90d24021367b05fda94ca4442036.zip | |
config: Minor changes to example-extras.cfg documentation
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Diffstat (limited to 'config/example-extras.cfg')
| -rw-r--r-- | config/example-extras.cfg | 21 |
1 files changed, 10 insertions, 11 deletions
diff --git a/config/example-extras.cfg b/config/example-extras.cfg index 805da97c..28e9e0e5 100644 --- a/config/example-extras.cfg +++ b/config/example-extras.cfg @@ -11,9 +11,9 @@ # Z height probe. One may define this section to enable Z height # probing hardware. When this section is enabled, PROBE and # QUERY_PROBE extended g-code commands become available. The probe -# section also creates a virtual probe:z_virtual_endstop pin. One may -# set the stepper_z endstop_pin to this virtual pin on cartesian style -# printers that use the probe in place of a z endstop. +# section also creates a virtual "probe:z_virtual_endstop" pin. One +# may set the stepper_z endstop_pin to this virtual pin on cartesian +# style printers that use the probe in place of a z endstop. #[probe] #pin: ar15 # Probe detection pin. This parameter must be provided. @@ -350,8 +350,8 @@ # Run-time configurable output pins (one may define any number of # sections with an "output_pin" prefix). Pins configured here will be -# setup as output pins and one may modify them at run-time using the -# "SET_PIN PIN=my_pin VALUE=.1" extended g-code command. +# setup as output pins and one may modify them at run-time using +# "SET_PIN PIN=my_pin VALUE=.1" type extended g-code commands. #[output_pin my_pin] #pin: # The pin to configure as an output. This parameter must be @@ -367,8 +367,8 @@ # slightly less ram in the micro-controller. The default is to use # runtime configuration of pins. #value: -# The value to initially set the pin to during MCU -# configuration. The default is 0 (for low voltage). +# The value to initially set the pin to during MCU configuration. +# The default is 0 (for low voltage). #shutdown_value: # The value to set the pin to on an MCU shutdown event. The default # is 0 (for low voltage). @@ -420,9 +420,8 @@ # The value to statically set the given AD5206 channel to. This is # typically set to a number between 0.0 and 1.0 with 1.0 being the # highest resistance and 0.0 being the lowest resistance. However, -# the range may be changed with the 'scale' parameter (see -# below). If a channel is not specified then it is left -# unconfigured. +# the range may be changed with the 'scale' parameter (see below). +# If a channel is not specified then it is left unconfigured. #scale: # This parameter can be used to alter how the 'channel_x' parameters # are interpreted. If provided, then the 'channel_x' parameters @@ -565,7 +564,7 @@ # used in "RepRapDiscount 2004 Smart Controller" type displays), # "st7920" (which is used in "RepRapDiscount 12864 Full Graphic # Smart Controller" type displays) or "uc1701" (which is used in -# "MKS Mini 12864 type" displays). This parameter must be provided. +# "MKS Mini 12864" type displays). This parameter must be provided. #rs_pin: #e_pin: #d4_pin: |