diff options
| author | dahliamoth <110364527+dahliamoth@users.noreply.github.com> | 2023-02-28 11:41:02 -0600 |
|---|---|---|
| committer | GitHub <noreply@github.com> | 2023-02-28 12:41:02 -0500 |
| commit | e6ef48cdf7b7e23f422cbe0ec46091001b840674 (patch) | |
| tree | f83d8641b4113630faaaaa78bb4365edbf6ad5c9 | |
| parent | a5fb20765e9f3872a21ab0debb7c9b46bc119ffd (diff) | |
| download | kutter-e6ef48cdf7b7e23f422cbe0ec46091001b840674.tar.gz kutter-e6ef48cdf7b7e23f422cbe0ec46091001b840674.tar.xz kutter-e6ef48cdf7b7e23f422cbe0ec46091001b840674.zip | |
config: Update printer-sunlu-t3-2022.cfg (#6040)
Fix filament sensor and remove unneeded config changes in extruder
The filament sensor on the printer used for initial testing had been removed prior to flashing klipper to it. Only a basic test to see it if triggered or not was preformed. It was discovered by someone else doing some testing on another printer that it would frequently pause. This was a simple oversight, assuming it was a runout switch.
Removed section of config related to filament runout switch and replaced with basic config for filament motion so they printer will simply pause when no more motion is detected. Also notated to add CLEAR_PAUSE to start gcode if using this sensor as it will trigger a paused state when loading or unloading filament. If printer is in a paused state at the start of the print, the attempt to pause will cause the printer to rapidly pause and unpause itself.
Removed min_extruder_temp and max_extrude_only_distance from the extruder section, as they were there only for macros on a test system that is not put into this sample config
Signed-off-by: Zachary Welvaert <zwelvaert@gmail.com>
| -rw-r--r-- | config/printer-sunlu-t3-2022.cfg | 27 |
1 files changed, 13 insertions, 14 deletions
diff --git a/config/printer-sunlu-t3-2022.cfg b/config/printer-sunlu-t3-2022.cfg index 90086681..f9bf2624 100644 --- a/config/printer-sunlu-t3-2022.cfg +++ b/config/printer-sunlu-t3-2022.cfg @@ -20,7 +20,7 @@ [mcu] #obtain your MCU id using ls /dev/serial/by-path/* -serial: dev/serial/by-id/usb-Klipper_stm32f103xe_833E31383534300530343833-if00 +serial: dev/serial/by-id/usb-Klipper_stm32f103xe_00000000000 [printer] kinematics: cartesian @@ -37,7 +37,7 @@ sensor_pin: PC14 control_pin: PA1 x_offset: -28.45 y_offset: 4 -z_offset: 1.915 #recheck you own +z_offset: 1.915 pin_up_touch_mode_reports_triggered: FALSE #needed bc of the bltouch clone used by sunlu [safe_z_home] @@ -66,13 +66,14 @@ screw3_name: Rear Right screw4: 31,204 #X,Y Position screw4_name: Rear Left -[filament_switch_sensor Filament_Runout] -pause_on_runout: True -#runout_gcode: -#insert_gcode: -event_delay: 3.0 -pause_delay: 5 -switch_pin: !PC15 #if reads runout when loaded remove ! +##IMPORTANT. If using the filament sensor add CLEAR_PAUSE to your slicer's start gcode or to your print start macro.## +##The act of loading and unloading filament will trigger a paused state## +[filament_motion_sensor Filament_Sensor] +detection_length: 7.0 +extruder: extruder +switch_pin: !PC15 +pause_on_runout: FALSE +runout_gcode: PAUSE ######################################################### # Motion Axis @@ -118,18 +119,16 @@ step_pin: PB3 dir_pin: !PB4 enable_pin: !PD2 microsteps: 16 -rotation_distance: 23.18840579710145 #verify your own +rotation_distance: 23.18840579710145 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: PC8 sensor_type: EPCOS 100K B57560G104F sensor_pin: PA0 control: pid -pid_Kp: 19.479 #calibrate your own PID +pid_Kp: 19.479 pid_Ki: 1.073 pid_Kd: 88.385 -min_extrude_temp: 175 -max_extrude_only_distance: 400 min_temp: 0 max_temp: 250 @@ -138,7 +137,7 @@ heater_pin: PC9 sensor_type: EPCOS 100K B57560G104F sensor_pin: PC3 control: pid -pid_Kp: 62.673 #calibrate your own PID +pid_Kp: 62.673 pid_Ki: 1.530 pid_Kd: 641.619 min_temp: 0 |