config: Remove tmc interpolate setting from example configs

There is no reason to explicitly set the interpolate flag to true in
the example configs as that is already the default.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

3 files changed, 0 insertions, 19 deletions

diff --git a/config/generic-bigtreetech-gtr.cfg b/config/generic-bigtreetech-gtr.cfg
index a562afee..7e0b126f 100644
--- a/config/generic-bigtreetech-gtr.cfg
+++ b/config/generic-bigtreetech-gtr.cfg
@@ -218,7 +218,6 @@ max_z_accel: 5
 #[tmc5160 stepper_x]
 #cs_pin: PC14
 #sense_resistor: 0.075
-#interpolate: True
 #run_current: 1
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
@@ -228,7 +227,6 @@ max_z_accel: 5
 #[tmc5160 stepper_y]
 #cs_pin: PE1
 #sense_resistor: 0.075
-#interpolate: True
 #run_current: 1
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
@@ -238,7 +236,6 @@ max_z_accel: 5
 #[tmc5160 stepper_z]
 #cs_pin: PB5
 #sense_resistor: 0.075
-#interpolate: True
 #run_current: 0.4
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
@@ -248,7 +245,6 @@ max_z_accel: 5
 #[tmc5160 extruder]
 #cs_pin: PG10
 #sense_resistor: 0.075
-#interpolate: True
 #run_current: 0.5
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
@@ -258,7 +254,6 @@ max_z_accel: 5
 #[tmc5160 extruder1]
 #cs_pin: PD4
 #sense_resistor: 0.075
-#interpolate: True
 #run_current: 0.800
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
@@ -268,7 +263,6 @@ max_z_accel: 5
 #[tmc5160 extruder2]
 #cs_pin: PC12
 #sense_resistor: 0.075
-#interpolate: True
 #run_current: 0.800
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
diff --git a/config/generic-duet2-duex.cfg b/config/generic-duet2-duex.cfg
index 5b06c6a4..38903ed2 100644
--- a/config/generic-duet2-duex.cfg
+++ b/config/generic-duet2-duex.cfg
@@ -96,7 +96,6 @@ position_max: 250
 [tmc2660 stepper_x]
 cs_pin: PD14 # X_SPI_EN Required for communication
 spi_bus: usart1 # All TMC2660 drivers are connected to USART1
-interpolate: True # 1/16 micro-steps interpolated to 1/256
 run_current: 1.000
 sense_resistor: 0.051
 idle_current_percent: 20
@@ -114,7 +113,6 @@ position_max: 210
 [tmc2660 stepper_y]
 cs_pin: PC9
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 idle_current_percent: 20
@@ -132,7 +130,6 @@ position_max: 200
 [tmc2660 stepper_z]
 cs_pin: PC10
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 
@@ -147,7 +144,6 @@ rotation_distance: 8
 [tmc2660 stepper_z1]
 cs_pin: PD25
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 
@@ -162,7 +158,6 @@ rotation_distance: 8
 [tmc2660 stepper_z2]
 cs_pin: PD26
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 
@@ -177,7 +172,6 @@ rotation_distance: 8
 [tmc2660 stepper_z3]
 cs_pin: PB14
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 
@@ -203,7 +197,6 @@ max_temp: 250
 [tmc2660 extruder]
 cs_pin: PC17
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 
@@ -229,7 +222,6 @@ max_temp: 250
 [tmc2660 extruder1]
 cs_pin: PC25
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 
@@ -255,7 +247,6 @@ max_temp: 250
 [tmc2660 extruder2]
 cs_pin: PD23
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 
@@ -281,7 +272,6 @@ max_temp: 250
 [tmc2660 extruder3]
 cs_pin: PD24
 spi_bus: usart1
-interpolate: True
 run_current: 1.000
 sense_resistor: 0.051
 
diff --git a/config/sample-mmu2s-diy.cfg b/config/sample-mmu2s-diy.cfg
index 80e8c058..d1d7793e 100644
--- a/config/sample-mmu2s-diy.cfg
+++ b/config/sample-mmu2s-diy.cfg
@@ -36,7 +36,6 @@ endstop_pin: ^mmboard:PC2 # PINDA X+
 [tmc2208 manual_stepper gear_stepper]
 uart_pin: mmboard:PC14
 run_current: 1.000
-interpolate: True
 sense_resistor: 0.110
 
 # Y : MMU2S idler with the 5 ball bearings
@@ -52,7 +51,6 @@ accel: 80
 [tmc2209 manual_stepper idler_stepper]
 uart_pin: mmboard:PB7
 run_current: 0.800
-interpolate: True
 sense_resistor: 0.110
 stealthchop_threshold: 999999
 
@@ -71,7 +69,6 @@ endstop_pin: !mmboard:PC0 # switch endstop on the left Z-
 [tmc2209 manual_stepper selector_stepper]
 uart_pin: mmboard:PC12
 run_current: 1.000
-interpolate: True
 sense_resistor: 0.110
 stealthchop_threshold: 999999