config: Config for Anycubic 4MaxPro_2.0-2021 (#4557)

This config I created and fully tested on my own printer Anycubic 4Max Pro 2.0. This works fine! Please note that this printer is different from the Anycubic 4MAX.

Signed-off-by: Alexander Usachev <int_0x21@protonmail.com>

2 files changed, 142 insertions, 0 deletions

diff --git a/config/printer-anycubic-4maxpro-2.0-2021.cfg b/config/printer-anycubic-4maxpro-2.0-2021.cfg
new file mode 100644
index 00000000..f87fce49
--- /dev/null
+++ b/config/printer-anycubic-4maxpro-2.0-2021.cfg
@@ -0,0 +1,141 @@
+# Klipper firmware config file for Anycubic 4Max Pro 2.0. To use this config,
+# the firmware should be compiled for the AVR atmega2560.
+
+# You can build and flash firmware with commands in klipper directory:
+# $ make clean
+# $ make menuconfig
+# $ make
+# $ make flash FLASH_DEVICE={your serial port}
+
+# For more precision, don't forget calibrate PIDs individually for your printer.
+
+# For Anycubic 4Max Pro (not 2.0) owners:
+#       Be careful when using this config! This config tested only on Anycubic
+#       4Max Pro 2.0 with klipper v0.9.1-667-g31761500! At first, you should
+#       set homing_speed on 5, and run homing and click on the endstops with
+#       your fingers. It is necessary to make sure that all the motors are
+#       spinning in the right direction, all the temperature sensors show the
+#       correct values, and all the endstops are triggered correctly.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PF0
+dir_pin: PF1
+enable_pin: !PD7
+rotation_distance: 32
+microsteps: 16
+endstop_pin: ^!PE5
+position_min: -8
+position_endstop: -8
+position_max: 270
+homing_speed: 50.0
+homing_retract_dist: 5.0
+second_homing_speed: 5.0
+
+[stepper_y]
+step_pin: PF6
+dir_pin: !PF7
+enable_pin: !PF2
+rotation_distance: 40
+microsteps: 16
+endstop_pin: ^!PD2
+position_max: 215
+position_min: -1
+position_endstop: -1
+homing_speed: 50.0
+homing_retract_dist: 5.0
+second_homing_speed: 5.0
+
+[stepper_z]
+step_pin: PL3
+dir_pin: PL1
+enable_pin: !PK0
+rotation_distance: 4
+microsteps: 16
+endstop_pin: ^!PD3
+position_endstop: 0.0
+position_max: 195
+homing_speed: 5.0
+homing_retract_dist: 3.0
+second_homing_speed: 0.8
+homing_speed: 6.0
+
+[extruder]
+step_pin: PA4
+dir_pin: !PA6
+enable_pin: !PA2
+microsteps: 16
+rotation_distance: 7.488
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+instantaneous_corner_velocity: 1.5
+max_extrude_only_distance: 500
+heater_pin: PB4
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: PK5
+smooth_time: 2
+control: pid
+pid_kp: 29.735      # calibrate these PID values for your printer individually!
+pid_ki: 1.304       # calibrate these PID values for your printer individually!
+pid_kd: 169.491     # calibrate these PID values for your printer individually!
+min_temp: 0
+max_temp: 280
+
+[heater_bed]
+heater_pin: PH5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PK6
+control: pid
+pid_kp: 71.423       # calibrate these PID values for your printer individually!
+pid_ki: 0.679        # calibrate these PID values for your printer individually!
+pid_kd: 1877.522     # calibrate these PID values for your printer individually!
+min_temp: 0
+max_temp: 125
+
+[fan]
+pin: PH6
+kick_start_time: 1.0
+
+[heater_fan heatbreak_fan]
+pin: PL5
+kick_start_time: 1.0
+max_power: 1.0
+heater_temp: 40.0
+heater: extruder
+
+[controller_fan system_fan]
+pin: PH4
+hardware_pwm: True
+kick_start_time: 1.0
+max_power: 1.0
+idle_timeout: 300
+idle_speed: 0.5
+shutdown_speed: 1.0
+heater: heater_bed,extruder
+
+[output_pin light]
+value: 1
+pin: PL4
+
+[mcu]
+serial: /dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0
+restart_method: arduino
+
+[printer]
+kinematics: cartesian
+max_velocity: 150
+max_accel: 3000
+max_accel_to_decel: 1500
+max_z_velocity: 7
+max_z_accel: 50
+square_corner_velocity: 5
+
+[bed_screws]
+screw1: 5,5
+screw2: 265,210
+screw3: 5,210
+screw4: 265,5
+
+[filament_switch_sensor filament_sensor]
+switch_pin: ^!PC4
diff --git a/test/klippy/printers.test b/test/klippy/printers.test
index fa7bd79e..dcb7fb67 100644
--- a/test/klippy/printers.test
+++ b/test/klippy/printers.test
@@ -25,6 +25,7 @@ CONFIG ../../config/generic-ultimaker-ultimainboard-v2.cfg
 CONFIG ../../config/kit-zav3d-2019.cfg
 CONFIG ../../config/printer-adimlab-2018.cfg
 CONFIG ../../config/printer-anycubic-4max-2018.cfg
+CONFIG ../../config/printer-anycubic-4maxpro-2.0-2021.cfg
 CONFIG ../../config/printer-anycubic-i3-mega-2017.cfg
 CONFIG ../../config/printer-anycubic-kossel-2016.cfg
 CONFIG ../../config/printer-anycubic-kossel-plus-2017.cfg