config: Additional formatting changes to example-extras.cfg

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

1 files changed, 20 insertions, 18 deletions

diff --git a/config/example-extras.cfg b/config/example-extras.cfg
index 73e5cc19..b18c3c34 100644
--- a/config/example-extras.cfg
+++ b/config/example-extras.cfg
@@ -181,15 +181,15 @@
 #   to a probe_height position. The default is 5.
 
 # Tool to help adjust bed screws tilt using Z probe. One may define a
-# [screws_tilt_adjust] config section to enable a SCREWS_TILT_CALCULATE
-# g-code command.
+# [screws_tilt_adjust] config section to enable a
+# SCREWS_TILT_CALCULATE g-code command.
 #[screws_tilt_adjust]
 #screw1: 100,100
 #   The X,Y coordinate of the first bed leveling screw. This is a
 #   position to command the nozzle to that is directly above the bed
 #   screw (or as close as possible while still being above the bed).
-#   This is the base screw used in calculations.
-#   This parameter must be provided.
+#   This is the base screw used in calculations. This parameter must
+#   be provided.
 #screw1_name: front screw
 #   An arbitrary name for the given screw. This name is displayed when
 #   the helper script runs. The default is to use a name based upon
@@ -239,7 +239,8 @@
 #   The height (in mm) that the head should be commanded to move to
 #   just prior to starting a probe operation. The default is 5.
 #retries: 0
-#   Number of times to retry if the probed points aren't within tolerance
+#   Number of times to retry if the probed points aren't within
+#   tolerance.
 #retry_tolerance: 0
 #   If retries are enabled then retry if largest and smallest probed
 #   points differ more than retry_tolerance. Note the smallest unit of
@@ -253,8 +254,8 @@
 # which is more flexible.
 # WARNING: Using this on a moving bed may lead to undesirable results.
 # If this section is present then a QUAD_GANTRY_LEVEL extended G-Code
-# command becomes available. This routine assumes the following Z motor
-# configuration:
+# command becomes available. This routine assumes the following Z
+# motor configuration:
 # ----------------
 # |Z1          Z2|
 # |  ---------   |
@@ -311,8 +312,8 @@
 #   A X,Y coordinate (e.g. 100,100) where the Z homing should be
 #   performed. This parameter must be provided.
 #speed: 50.0
-#   Speed at which the toolhead is moved to the safe Z home coordinate.
-#   The default is 50 mm/s
+#   Speed at which the toolhead is moved to the safe Z home
+#   coordinate. The default is 50 mm/s
 #z_hop:
 #   Lift the Z axis prior to homing. This is applied to any homing
 #   command, even if it doesn't home the Z axis. If the Z axis is
@@ -479,7 +480,8 @@
 #   Set to true to enable FORCE_MOVE and SET_KINEMATIC_POSITION
 #   extended G-Code commands. The default is false.
 
-# Pause/Resume functionality with support of position capture and restore
+# Pause/Resume functionality with support of position capture and
+# restore.
 #[pause_resume]
 #recover_velocity: 50.
 #   When capture/restore is enabled, the speed at which to return to
@@ -515,8 +517,8 @@
 # Enable the "M118" and "RESPOND" extended commands.
 #[respond]
 #default_type: echo
-#   Sets the default prefix of the "M118" and "RESPOND" output to one of
-#   the following:
+#   Sets the default prefix of the "M118" and "RESPOND" output to one
+#   of the following:
 #       echo: "echo: " (This is the default)
 #       command: "// "
 #       error: "!! "
@@ -1693,8 +1695,8 @@
 #   The amount of current (in amps RMS) used by the driver during
 #   stepper movement. This parameter must be provided.
 #sense_resistor:
-#   The resistance (in ohms) of the motor sense resistor. This parameter
-#   must be provided.
+#   The resistance (in ohms) of the motor sense resistor. This
+#   parameter must be provided.
 #idle_current_percent: 100
 #   The percentage of the run_current the stepper driver will be
 #   lowered to when the idle timeout expires (you need to set up the
@@ -1726,10 +1728,10 @@
 #   chip. This may be used to set custom driver parameters. The
 #   defaults for each parameter are next to the parameter name in the
 #   list above. See the TMC2660 datasheet about what each parameter
-#   does and what the restrictions on parameter combinations are.
-#   Be especially aware of the CHOPCONF register, where setting CHM to
-#   either 0 or one will lead to layout changes (the first bit of HDEC)
-#   is interpreted as the MSB of HSTRT in this case).
+#   does and what the restrictions on parameter combinations are. Be
+#   especially aware of the CHOPCONF register, where setting CHM to
+#   either zero or one will lead to layout changes (the first bit of
+#   HDEC) is interpreted as the MSB of HSTRT in this case).
 
 # Configure a TMC5160 stepper motor driver via SPI bus. To use this
 # feature, define a config section with a "tmc5160" prefix followed by