docs: Add how to configure LIS2DW instructions

Signed-off-by: Alan.Ma from BigTreeTech tech@biqu3d.com

2 files changed, 45 insertions, 4 deletions

diff --git a/docs/Config_Reference.md b/docs/Config_Reference.md
index d0b617a3..5b8038f7 100644
--- a/docs/Config_Reference.md
+++ b/docs/Config_Reference.md
@@ -1646,6 +1646,27 @@ cs_pin:
 #   measurements.
 ```
 
+### [lis2dw]
+
+Support for LIS2DW accelerometers.
+
+```
+[lis2dw]
+cs_pin:
+#   The SPI enable pin for the sensor. This parameter must be provided.
+#spi_speed: 5000000
+#   The SPI speed (in hz) to use when communicating with the chip.
+#   The default is 5000000.
+#spi_bus:
+#spi_software_sclk_pin:
+#spi_software_mosi_pin:
+#spi_software_miso_pin:
+#   See the "common SPI settings" section for a description of the
+#   above parameters.
+#axes_map: x, y, z
+#   See the "adxl345" section for information on this parameter.
+```
+
 ### [mpu9250]
 
 Support for MPU-9250, MPU-9255, MPU-6515, MPU-6050, and MPU-6500
diff --git a/docs/Measuring_Resonances.md b/docs/Measuring_Resonances.md
index cf43e31d..28cda9d0 100644
--- a/docs/Measuring_Resonances.md
+++ b/docs/Measuring_Resonances.md
@@ -1,11 +1,11 @@
 # Measuring Resonances
 
-Klipper has built-in support for the ADXL345 and MPU-9250 compatible
+Klipper has built-in support for the ADXL345, MPU-9250 and LIS2DW compatible
 accelerometers which can be used to measure resonance frequencies of the printer
 for different axes, and auto-tune [input shapers](Resonance_Compensation.md) to
 compensate for resonances. Note that using accelerometers requires some
-soldering and crimping. The ADXL345 can be connected to the SPI interface of a
-Raspberry Pi or MCU board (it needs to be reasonably fast). The MPU family can
+soldering and crimping. The ADXL345/LIS2DW can be connected to the SPI interface
+of a Raspberry Pi or MCU board (it needs to be reasonably fast). The MPU family can
 be connected to the I2C interface of a Raspberry Pi directly, or to an I2C
 interface of an MCU board that supports 400kbit/s *fast mode* in Klipper.
 
@@ -13,7 +13,7 @@ When sourcing accelerometers, be aware that there are a variety of different PCB
 board designs and different clones of them. If it is going to be connected to a
 5V printer MCU ensure it has a voltage regulator and level shifters.
 
-For ADXL345s, make sure that the board supports SPI mode (a small number of
+For ADXL345s/LIS2DWs, make sure that the board supports SPI mode (a small number of
 boards appear to be hard-configured for I2C by pulling SDO to GND).
 
 For MPU-9250/MPU-9255/MPU-6515/MPU-6050/MPU-6500s there are also a variety of
@@ -305,6 +305,26 @@ you'll also want to modify your `printer.cfg` file to include this:
 
 Restart Klipper via the `RESTART` command.
 
+#### Configure LIS2DW series
+
+```
+[mcu lis]
+# Change <mySerial> to whatever you found above. For example,
+# usb-Klipper_rp2040_E661640843545B2E-if00
+serial: /dev/serial/by-id/usb-Klipper_rp2040_<mySerial>
+
+[lis2dw]
+cs_pin: lis:gpio1
+spi_bus: spi0a
+axes_map: x,z,y
+
+[resonance_tester]
+accel_chip: lis2dw
+probe_points:
+    # Somewhere slightly above the middle of your print bed
+    147,154, 20
+```
+
 #### Configure MPU-6000/9000 series With RPi
 
 Make sure the Linux I2C driver is enabled and the baud rate is