From 7a443e50e1dbf42eeef02b2983cb15f33722d45c Mon Sep 17 00:00:00 2001
From: Kevin O'Connor <kevin@koconnor.net>
Date: Fri, 19 Mar 2021 12:52:21 -0400
Subject: config: Don't use arduino mega aliases in example config files

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
---
 config/printer-sunlu-s8-2020.cfg | 59 ++++++++++++++++++++--------------------
 1 file changed, 29 insertions(+), 30 deletions(-)

(limited to 'config/printer-sunlu-s8-2020.cfg')

diff --git a/config/printer-sunlu-s8-2020.cfg b/config/printer-sunlu-s8-2020.cfg
index b933ced8..ccf07d21 100644
--- a/config/printer-sunlu-s8-2020.cfg
+++ b/config/printer-sunlu-s8-2020.cfg
@@ -1,53 +1,53 @@
 # This file contains pin mappings for the SUNLU S8 v1.01 (circa 2020), which
 # is a modified RAMPS v1.3 board. To use this config, the firmware should be
 # compiled for the AVR atmega2560. The following pins are available for
-# expansion (e.g. ABL): ^ar19 (Z+ endstop), ar4, ar5, ar6, ar11
+# expansion (e.g. ABL): ^PD2 (Z+ endstop), PG5, PE3, PH3, PB5
 
 # See docs/Config_Reference.md for a description of parameters.
 
 [stepper_x]
-step_pin: ar54
-dir_pin: !ar55
-enable_pin: !ar38
+step_pin: PF0
+dir_pin: !PF1
+enable_pin: !PD7
 microsteps: 16
 rotation_distance: 40
-endstop_pin: ^!ar3
+endstop_pin: ^!PE5
 position_endstop: 0
 position_max: 310
 homing_speed: 50
 
 [stepper_y]
-step_pin: ar60
-dir_pin: !ar61
-enable_pin: !ar56
+step_pin: PF6
+dir_pin: !PF7
+enable_pin: !PF2
 microsteps: 16
 rotation_distance: 40
-endstop_pin: ^!ar14
+endstop_pin: ^!PJ1
 position_endstop: 0
 position_max: 310
 homing_speed: 50
 
 [stepper_z]
-step_pin: ar46
-dir_pin: ar48
-enable_pin: !ar62
+step_pin: PL3
+dir_pin: PL1
+enable_pin: !PK0
 microsteps: 16
 rotation_distance: 8
-endstop_pin: ^!ar18
+endstop_pin: ^!PD3
 position_endstop: 0.5
 position_max: 400
 
 [extruder]
-step_pin: ar26
-dir_pin: !ar28
-enable_pin: !ar24
+step_pin: PA4
+dir_pin: !PA6
+enable_pin: !PA2
 microsteps: 16
 rotation_distance: 33.280
 nozzle_diameter: 0.400
 filament_diameter: 1.750
-heater_pin: ar10
+heater_pin: PB4
 sensor_type: EPCOS 100K B57560G104F
-sensor_pin: analog13
+sensor_pin: PK5
 control: pid
 pid_kp: 25.588
 pid_ki: 1.496
@@ -57,12 +57,12 @@ max_temp: 250
 
 [filament_switch_sensor runout]
 pause_on_runout: True
-switch_pin: ^ar2
+switch_pin: ^PE4
 
 [heater_bed]
-heater_pin: ar8
+heater_pin: PH5
 sensor_type: EPCOS 100K B57560G104F
-sensor_pin: analog14
+sensor_pin: PK6
 control: pid
 pid_kp: 74.786
 pid_ki: 0.766
@@ -77,14 +77,13 @@ max_temp: 110
 check_gain_time: 240
 
 [fan]
-pin: ar9
+pin: PH6
 
 [heater_fan fan1]
-pin: ar7
+pin: PH4
 
 [mcu]
 serial: /dev/ttyUSB0
-pin_map: arduino
 
 [printer]
 kinematics: cartesian
@@ -95,11 +94,11 @@ max_z_accel: 100
 
 [display]
 lcd_type: st7920
-cs_pin: ar16
-sclk_pin: ar23
-sid_pin: ar17
-encoder_pins: ^ar33, ^ar31
-click_pin: ^!ar35
+cs_pin: PH1
+sclk_pin: PA1
+sid_pin: PH0
+encoder_pins: ^PC4, ^PC6
+click_pin: ^!PC2
 
 [output_pin beeper]
-pin: ar37
+pin: PC0
-- 
cgit v1.2.3-70-g09d2