From 7a443e50e1dbf42eeef02b2983cb15f33722d45c Mon Sep 17 00:00:00 2001
From: Kevin O'Connor <kevin@koconnor.net>
Date: Fri, 19 Mar 2021 12:52:21 -0400
Subject: config: Don't use arduino mega aliases in example config files

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
---
 config/generic-ramps.cfg | 69 ++++++++++++++++++++++++------------------------
 1 file changed, 34 insertions(+), 35 deletions(-)

(limited to 'config/generic-ramps.cfg')

diff --git a/config/generic-ramps.cfg b/config/generic-ramps.cfg
index 19e4653d..f2c5bc33 100644
--- a/config/generic-ramps.cfg
+++ b/config/generic-ramps.cfg
@@ -1,55 +1,55 @@
 # This file contains common pin mappings for RAMPS (v1.3 and later)
 # boards. RAMPS boards typically use a firmware compiled for the AVR
-# atmega2560 (though other AVR chips are also possible).
+# atmega2560 (though the atmega1280 is also possible).
 
 # See docs/Config_Reference.md for a description of parameters.
 
 [stepper_x]
-step_pin: ar54
-dir_pin: ar55
-enable_pin: !ar38
+step_pin: PF0
+dir_pin: PF1
+enable_pin: !PD7
 microsteps: 16
 rotation_distance: 40
-endstop_pin: ^ar3
-#endstop_pin: ^ar2
+endstop_pin: ^PE5
+#endstop_pin: ^PE4
 position_endstop: 0
 position_max: 200
 homing_speed: 50
 
 [stepper_y]
-step_pin: ar60
-dir_pin: !ar61
-enable_pin: !ar56
+step_pin: PF6
+dir_pin: !PF7
+enable_pin: !PF2
 microsteps: 16
 rotation_distance: 40
-endstop_pin: ^ar14
-#endstop_pin: ^ar15
+endstop_pin: ^PJ1
+#endstop_pin: ^PJ0
 position_endstop: 0
 position_max: 200
 homing_speed: 50
 
 [stepper_z]
-step_pin: ar46
-dir_pin: ar48
-enable_pin: !ar62
+step_pin: PL3
+dir_pin: PL1
+enable_pin: !PK0
 microsteps: 16
 rotation_distance: 8
-endstop_pin: ^ar18
-#endstop_pin: ^ar19
+endstop_pin: ^PD3
+#endstop_pin: ^PD2
 position_endstop: 0.5
 position_max: 200
 
 [extruder]
-step_pin: ar26
-dir_pin: ar28
-enable_pin: !ar24
+step_pin: PA4
+dir_pin: PA6
+enable_pin: !PA2
 microsteps: 16
 rotation_distance: 33.500
 nozzle_diameter: 0.400
 filament_diameter: 1.750
-heater_pin: ar10
+heater_pin: PB4
 sensor_type: EPCOS 100K B57560G104F
-sensor_pin: analog13
+sensor_pin: PK5
 control: pid
 pid_Kp: 22.2
 pid_Ki: 1.08
@@ -58,27 +58,26 @@ min_temp: 0
 max_temp: 250
 
 #[extruder1]
-#step_pin: ar36
-#dir_pin: ar34
-#enable_pin: !ar30
-#heater_pin: ar9
-#sensor_pin: analog15
+#step_pin: PC1
+#dir_pin: PC3
+#enable_pin: !PC7
+#heater_pin: PH6
+#sensor_pin: PK7
 #...
 
 [heater_bed]
-heater_pin: ar8
+heater_pin: PH5
 sensor_type: EPCOS 100K B57560G104F
-sensor_pin: analog14
+sensor_pin: PK6
 control: watermark
 min_temp: 0
 max_temp: 130
 
 [fan]
-pin: ar9
+pin: PH6
 
 [mcu]
 serial: /dev/ttyACM0
-pin_map: arduino
 
 [printer]
 kinematics: cartesian
@@ -91,12 +90,12 @@ max_z_accel: 100
 [board_pins]
 aliases:
     # Common EXP1 header found on many "all-in-one" ramps clones
-    EXP1_1=ar37, EXP1_3=ar17, EXP1_5=ar23, EXP1_7=ar27, EXP1_9=<GND>,
-    EXP1_2=ar35, EXP1_4=ar16, EXP1_6=ar25, EXP1_8=ar29, EXP1_10=<5V>,
+    EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
+    EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
     # EXP2 header
-    EXP2_1=ar50, EXP2_3=ar31, EXP2_5=ar33, EXP2_7=ar49, EXP2_9=<GND>,
-    EXP2_2=ar52, EXP2_4=ar53, EXP2_6=ar51, EXP2_8=ar41, EXP2_10=<RST>
+    EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
+    EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
     # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
-    # Note, some boards wire: EXP2_8=<RST>, EXP2_10=ar41
+    # Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0
 
 # See the sample-lcd.cfg file for definitions of common LCD displays.
-- 
cgit v1.2.3-70-g09d2