From a629b87ae07fdea3c8aeaec3c01fc3a95e49adff Mon Sep 17 00:00:00 2001 From: Kevin O'Connor Date: Mon, 30 Oct 2023 14:04:08 -0400 Subject: config: Split generic-bigtreetech-octopus.cfg into separate files Use two different files for the Octopus Pro and Octopus (non-Pro). The configs are the same in practice, but the difference in version and naming can lead to confusion. Signed-off-by: Kevin O'Connor --- config/generic-bigtreetech-octopus-pro-v1.0.cfg | 289 ++++++++++++++++++++++++ config/generic-bigtreetech-octopus-v1.1.cfg | 288 +++++++++++++++++++++++ config/generic-bigtreetech-octopus.cfg | 284 ----------------------- test/klippy/printers.test | 6 +- 4 files changed, 582 insertions(+), 285 deletions(-) create mode 100644 config/generic-bigtreetech-octopus-pro-v1.0.cfg create mode 100644 config/generic-bigtreetech-octopus-v1.1.cfg delete mode 100644 config/generic-bigtreetech-octopus.cfg diff --git a/config/generic-bigtreetech-octopus-pro-v1.0.cfg b/config/generic-bigtreetech-octopus-pro-v1.0.cfg new file mode 100644 index 00000000..7a5eeafb --- /dev/null +++ b/config/generic-bigtreetech-octopus-pro-v1.0.cfg @@ -0,0 +1,289 @@ +# This file contains common pin mappings for the BigTreeTech Octopus +# Pro v1.0 board. + +# Important! Do not use this config with an Octopus Pro v1.1 board as +# doing so could result in a heater being inadvertently enabled. + +# To use this config, start by identifying the micro-controller on the +# board - it may be an STM32F446, STM32F429, or an STM32H723. Select +# the appropriate micro-controller in "make menuconfig" and select +# "Enable low-level configuration options". For STM32F446 boards the +# firmware should be compiled with a "32KiB bootloader" and a "12MHz +# crystal" clock reference. For STM32F429 boards use a "32KiB +# bootloader" and an "8MHz crystal". For STM32H723 boards use a +# "128KiB bootloader" and a "25Mhz crystal". + +# See docs/Config_Reference.md for a description of parameters. + +# Driver0 +[stepper_x] +step_pin: PF13 +dir_pin: PF12 +enable_pin: !PF14 +microsteps: 16 +rotation_distance: 40 +endstop_pin: PG6 +position_endstop: 0 +position_max: 200 +homing_speed: 50 + +# Driver1 +[stepper_y] +step_pin: PG0 +dir_pin: PG1 +enable_pin: !PF15 +microsteps: 16 +rotation_distance: 40 +endstop_pin: PG9 +position_endstop: 0 +position_max: 200 +homing_speed: 50 + +# Driver2 +[stepper_z] +step_pin: PF11 +dir_pin: PG3 +enable_pin: !PG5 +microsteps: 16 +rotation_distance: 8 +endstop_pin: PG10 +position_endstop: 0.5 +position_max: 200 + +# Driver3 +# The Octopus only has 4 heater outputs which leaves an extra stepper +# This can be used for a second Z stepper, dual_carriage, extruder co-stepper, +# or other accesory such as an MMU +#[stepper_] +#step_pin: PG4 +#dir_pin: PC1 +#enable_pin: PA0 +#endstop_pin: PG11 +#... + +# Driver4 +[extruder] +step_pin: PF9 +dir_pin: PF10 +enable_pin: !PG2 +microsteps: 16 +rotation_distance: 33.500 +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PA2 # HE0 +sensor_pin: PF4 # T0 +sensor_type: EPCOS 100K B57560G104F +control: pid +pid_Kp: 22.2 +pid_Ki: 1.08 +pid_Kd: 114 +min_temp: 0 +max_temp: 250 + +#[filament_switch_sensor material_0] +#switch_pin: PG12 + +# Driver5 +#[extruder1] +#step_pin: PC13 +#dir_pin: PF0 +#enable_pin: !PF1 +#heater_pin: PA3 # HE1 +#sensor_pin: PF5 # T1 +#... + +#[filament_switch_sensor material_1] +#switch_pin: PG13 + +# Driver6 +#[extruder2] +#step_pin: PE2 +#dir_pin: PE3 +#enable_pin: !PD4 +#heater_pin: PB10 # HE2 +#sensor_pin: PF6 # T2 +#... + +#[filament_switch_sensor material_2] +#switch_pin: PG14 + +# Driver7 +#[extruder3] +#step_pin: PE6 +#dir_pin: PA14 +#enable_pin: !PE0 +#heater_pin: PB11 # HE3 +#sensor_pin: PF7 # T3 +#... + +#[filament_switch_sensor material_3] +#switch_pin: PG15 + +[heater_bed] +heater_pin: PA1 +sensor_pin: PF3 # TB +sensor_type: ATC Semitec 104GT-2 +control: watermark +min_temp: 0 +max_temp: 130 + +[fan] +pin: PA8 + +#[heater_fan fan1] +#pin: PE5 + +#[heater_fan fan2] +#pin: PD12 + +#[heater_fan fan3] +#pin: PD13 + +#[heater_fan fan4] +#pin: PD14 + +#[controller_fan fan5] +#pin: PD15 + +[mcu] +serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00 +# CAN bus is also available on this board + +[printer] +kinematics: cartesian +max_velocity: 300 +max_accel: 3000 +max_z_velocity: 5 +max_z_accel: 100 + +######################################## +# TMC2209 configuration +######################################## + +#[tmc2209 stepper_x] +#uart_pin: PC4 +##diag_pin: PG6 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 stepper_y] +#uart_pin: PD11 +##diag_pin: PG9 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 stepper_z] +#uart_pin: PC6 +##diag_pin: PG10 +#run_current: 0.650 +#stealthchop_threshold: 999999 + +#[tmc2209 stepper_] +#uart_pin: PC7 +##diag_pin: PG11 +#run_current: 0.650 +#stealthchop_threshold: 999999 + +#[tmc2209 extruder] +#uart_pin: PF2 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 extruder1] +#uart_pin: PE4 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 extruder2] +#uart_pin: PE1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 extruder3] +#uart_pin: PD3 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +######################################## +# TMC2130 configuration +######################################## + +#[tmc2130 stepper_x] +#cs_pin: PC4 +#spi_bus: spi1 +##diag1_pin: PG6 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 stepper_y] +#cs_pin: PD11 +#spi_bus: spi1 +##diag1_pin: PG9 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 stepper_z] +#cs_pin: PC6 +#spi_bus: spi1 +##diag1_pin: PG10 +#run_current: 0.650 +#stealthchop_threshold: 999999 + +#[tmc2130 stepper_] +#cs_pin: PC7 +#spi_bus: spi1 +##diag1_pin: PG11 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 extruder] +#cs_pin: PF2 +#spi_bus: spi1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 extruder1] +#cs_pin: PE4 +#spi_bus: spi1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 extruder2] +#cs_pin: PE1 +#spi_bus: spi1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 extruder3] +#cs_pin: PD3 +#spi_bus: spi1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +[board_pins] +aliases: + # EXP1 header + EXP1_1=PE8, EXP1_2=PE7, + EXP1_3=PE9, EXP1_4=PE10, + EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side + EXP1_7=PE14, EXP1_8=PE15, + EXP1_9=, EXP1_10=<5V>, + + # EXP2 header + EXP2_1=PA6, EXP2_2=PA5, + EXP2_3=PB1, EXP2_4=PA4, + EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side + EXP2_7=PC15, EXP2_8=, + EXP2_9=, EXP2_10=PC5 + +# See the sample-lcd.cfg file for definitions of common LCD displays. + +# A [probe] section can be defined instead with a pin: setting identical +# to the sensor_pin: for a bltouch +#[bltouch] +#sensor_pin: PB7 +#control_pin: PB6 +#z_offset: 0 + +#[neopixel my_neopixel] +#pin: PB0 diff --git a/config/generic-bigtreetech-octopus-v1.1.cfg b/config/generic-bigtreetech-octopus-v1.1.cfg new file mode 100644 index 00000000..d90f6f66 --- /dev/null +++ b/config/generic-bigtreetech-octopus-v1.1.cfg @@ -0,0 +1,288 @@ +# This file contains common pin mappings for the BigTreeTech Octopus +# (non-Pro) boards. + +# Important! Do not use this config with an Octopus Pro v1.1 board as +# doing so could result in a heater being inadvertently enabled. + +# To use this config, start by identifying the micro-controller on the +# board - it may be an STM32F446, or STM32F429. Select the +# appropriate micro-controller in "make menuconfig" and select "Enable +# low-level configuration options". For STM32F446 boards the firmware +# should be compiled with a "32KiB bootloader" and a "12MHz crystal" +# clock reference. For STM32F429 boards use a "32KiB bootloader" and +# an "8MHz crystal". + +# See docs/Config_Reference.md for a description of parameters. + +# Driver0 +[stepper_x] +step_pin: PF13 +dir_pin: PF12 +enable_pin: !PF14 +microsteps: 16 +rotation_distance: 40 +endstop_pin: PG6 +position_endstop: 0 +position_max: 200 +homing_speed: 50 + +# Driver1 +[stepper_y] +step_pin: PG0 +dir_pin: PG1 +enable_pin: !PF15 +microsteps: 16 +rotation_distance: 40 +endstop_pin: PG9 +position_endstop: 0 +position_max: 200 +homing_speed: 50 + +# Driver2 +[stepper_z] +step_pin: PF11 +dir_pin: PG3 +enable_pin: !PG5 +microsteps: 16 +rotation_distance: 8 +endstop_pin: PG10 +position_endstop: 0.5 +position_max: 200 + +# Driver3 +# The Octopus only has 4 heater outputs which leaves an extra stepper +# This can be used for a second Z stepper, dual_carriage, extruder co-stepper, +# or other accesory such as an MMU +#[stepper_] +#step_pin: PG4 +#dir_pin: PC1 +#enable_pin: PA0 +#endstop_pin: PG11 +#... + +# Driver4 +[extruder] +step_pin: PF9 +dir_pin: PF10 +enable_pin: !PG2 +microsteps: 16 +rotation_distance: 33.500 +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PA2 # HE0 +sensor_pin: PF4 # T0 +sensor_type: EPCOS 100K B57560G104F +control: pid +pid_Kp: 22.2 +pid_Ki: 1.08 +pid_Kd: 114 +min_temp: 0 +max_temp: 250 + +#[filament_switch_sensor material_0] +#switch_pin: PG12 + +# Driver5 +#[extruder1] +#step_pin: PC13 +#dir_pin: PF0 +#enable_pin: !PF1 +#heater_pin: PA3 # HE1 +#sensor_pin: PF5 # T1 +#... + +#[filament_switch_sensor material_1] +#switch_pin: PG13 + +# Driver6 +#[extruder2] +#step_pin: PE2 +#dir_pin: PE3 +#enable_pin: !PD4 +#heater_pin: PB10 # HE2 +#sensor_pin: PF6 # T2 +#... + +#[filament_switch_sensor material_2] +#switch_pin: PG14 + +# Driver7 +#[extruder3] +#step_pin: PE6 +#dir_pin: PA14 +#enable_pin: !PE0 +#heater_pin: PB11 # HE3 +#sensor_pin: PF7 # T3 +#... + +#[filament_switch_sensor material_3] +#switch_pin: PG15 + +[heater_bed] +heater_pin: PA1 +sensor_pin: PF3 # TB +sensor_type: ATC Semitec 104GT-2 +control: watermark +min_temp: 0 +max_temp: 130 + +[fan] +pin: PA8 + +#[heater_fan fan1] +#pin: PE5 + +#[heater_fan fan2] +#pin: PD12 + +#[heater_fan fan3] +#pin: PD13 + +#[heater_fan fan4] +#pin: PD14 + +#[controller_fan fan5] +#pin: PD15 + +[mcu] +serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00 +# CAN bus is also available on this board + +[printer] +kinematics: cartesian +max_velocity: 300 +max_accel: 3000 +max_z_velocity: 5 +max_z_accel: 100 + +######################################## +# TMC2209 configuration +######################################## + +#[tmc2209 stepper_x] +#uart_pin: PC4 +##diag_pin: PG6 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 stepper_y] +#uart_pin: PD11 +##diag_pin: PG9 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 stepper_z] +#uart_pin: PC6 +##diag_pin: PG10 +#run_current: 0.650 +#stealthchop_threshold: 999999 + +#[tmc2209 stepper_] +#uart_pin: PC7 +##diag_pin: PG11 +#run_current: 0.650 +#stealthchop_threshold: 999999 + +#[tmc2209 extruder] +#uart_pin: PF2 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 extruder1] +#uart_pin: PE4 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 extruder2] +#uart_pin: PE1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2209 extruder3] +#uart_pin: PD3 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +######################################## +# TMC2130 configuration +######################################## + +#[tmc2130 stepper_x] +#cs_pin: PC4 +#spi_bus: spi1 +##diag1_pin: PG6 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 stepper_y] +#cs_pin: PD11 +#spi_bus: spi1 +##diag1_pin: PG9 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 stepper_z] +#cs_pin: PC6 +#spi_bus: spi1 +##diag1_pin: PG10 +#run_current: 0.650 +#stealthchop_threshold: 999999 + +#[tmc2130 stepper_] +#cs_pin: PC7 +#spi_bus: spi1 +##diag1_pin: PG11 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 extruder] +#cs_pin: PF2 +#spi_bus: spi1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 extruder1] +#cs_pin: PE4 +#spi_bus: spi1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 extruder2] +#cs_pin: PE1 +#spi_bus: spi1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +#[tmc2130 extruder3] +#cs_pin: PD3 +#spi_bus: spi1 +#run_current: 0.800 +#stealthchop_threshold: 999999 + +[board_pins] +aliases: + # EXP1 header + EXP1_1=PE8, EXP1_2=PE7, + EXP1_3=PE9, EXP1_4=PE10, + EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side + EXP1_7=PE14, EXP1_8=PE15, + EXP1_9=, EXP1_10=<5V>, + + # EXP2 header + EXP2_1=PA6, EXP2_2=PA5, + EXP2_3=PB1, EXP2_4=PA4, + EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side + EXP2_7=PC15, EXP2_8=, + EXP2_9=, EXP2_10=PC5 + +# See the sample-lcd.cfg file for definitions of common LCD displays. + +# A [probe] section can be defined instead with a pin: setting identical +# to the sensor_pin: for a bltouch +#[bltouch] +#sensor_pin: PB7 +#control_pin: PB6 +#z_offset: 0 + +#[neopixel my_neopixel] +#pin: PB0 diff --git a/config/generic-bigtreetech-octopus.cfg b/config/generic-bigtreetech-octopus.cfg deleted file mode 100644 index 73bd584c..00000000 --- a/config/generic-bigtreetech-octopus.cfg +++ /dev/null @@ -1,284 +0,0 @@ -# This file contains common pin mappings for the BigTreeTech Octopus -# and Octopus Pro boards. To use this config, start by identifying the -# micro-controller on the board - it may be an STM32F446, STM32F429, -# or an STM32H723. Select the appropriate micro-controller in "make -# menuconfig" and select "Enable low-level configuration options". For -# STM32F446 boards the firmware should be compiled with a "32KiB -# bootloader" and a "12MHz crystal" clock reference. For STM32F429 -# boards use a "32KiB bootloader" and an "8MHz crystal". For STM32H723 -# boards use a "128KiB bootloader" and a "25Mhz crystal". - -# See docs/Config_Reference.md for a description of parameters. - -# Driver0 -[stepper_x] -step_pin: PF13 -dir_pin: PF12 -enable_pin: !PF14 -microsteps: 16 -rotation_distance: 40 -endstop_pin: PG6 -position_endstop: 0 -position_max: 200 -homing_speed: 50 - -# Driver1 -[stepper_y] -step_pin: PG0 -dir_pin: PG1 -enable_pin: !PF15 -microsteps: 16 -rotation_distance: 40 -endstop_pin: PG9 -position_endstop: 0 -position_max: 200 -homing_speed: 50 - -# Driver2 -[stepper_z] -step_pin: PF11 -dir_pin: PG3 -enable_pin: !PG5 -microsteps: 16 -rotation_distance: 8 -endstop_pin: PG10 -position_endstop: 0.5 -position_max: 200 - -# Driver3 -# The Octopus only has 4 heater outputs which leaves an extra stepper -# This can be used for a second Z stepper, dual_carriage, extruder co-stepper, -# or other accesory such as an MMU -#[stepper_] -#step_pin: PG4 -#dir_pin: PC1 -#enable_pin: PA0 -#endstop_pin: PG11 -#... - -# Driver4 -[extruder] -step_pin: PF9 -dir_pin: PF10 -enable_pin: !PG2 -microsteps: 16 -rotation_distance: 33.500 -nozzle_diameter: 0.400 -filament_diameter: 1.750 -heater_pin: PA2 # HE0 -sensor_pin: PF4 # T0 -sensor_type: EPCOS 100K B57560G104F -control: pid -pid_Kp: 22.2 -pid_Ki: 1.08 -pid_Kd: 114 -min_temp: 0 -max_temp: 250 - -#[filament_switch_sensor material_0] -#switch_pin: PG12 - -# Driver5 -#[extruder1] -#step_pin: PC13 -#dir_pin: PF0 -#enable_pin: !PF1 -#heater_pin: PA3 # HE1 -#sensor_pin: PF5 # T1 -#... - -#[filament_switch_sensor material_1] -#switch_pin: PG13 - -# Driver6 -#[extruder2] -#step_pin: PE2 -#dir_pin: PE3 -#enable_pin: !PD4 -#heater_pin: PB10 # HE2 -#sensor_pin: PF6 # T2 -#... - -#[filament_switch_sensor material_2] -#switch_pin: PG14 - -# Driver7 -#[extruder3] -#step_pin: PE6 -#dir_pin: PA14 -#enable_pin: !PE0 -#heater_pin: PB11 # HE3 -#sensor_pin: PF7 # T3 -#... - -#[filament_switch_sensor material_3] -#switch_pin: PG15 - -[heater_bed] -heater_pin: PA1 -sensor_pin: PF3 # TB -sensor_type: ATC Semitec 104GT-2 -control: watermark -min_temp: 0 -max_temp: 130 - -[fan] -pin: PA8 - -#[heater_fan fan1] -#pin: PE5 - -#[heater_fan fan2] -#pin: PD12 - -#[heater_fan fan3] -#pin: PD13 - -#[heater_fan fan4] -#pin: PD14 - -#[controller_fan fan5] -#pin: PD15 - -[mcu] -serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00 -# CAN bus is also available on this board - -[printer] -kinematics: cartesian -max_velocity: 300 -max_accel: 3000 -max_z_velocity: 5 -max_z_accel: 100 - -######################################## -# TMC2209 configuration -######################################## - -#[tmc2209 stepper_x] -#uart_pin: PC4 -##diag_pin: PG6 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2209 stepper_y] -#uart_pin: PD11 -##diag_pin: PG9 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2209 stepper_z] -#uart_pin: PC6 -##diag_pin: PG10 -#run_current: 0.650 -#stealthchop_threshold: 999999 - -#[tmc2209 stepper_] -#uart_pin: PC7 -##diag_pin: PG11 -#run_current: 0.650 -#stealthchop_threshold: 999999 - -#[tmc2209 extruder] -#uart_pin: PF2 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2209 extruder1] -#uart_pin: PE4 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2209 extruder2] -#uart_pin: PE1 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2209 extruder3] -#uart_pin: PD3 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -######################################## -# TMC2130 configuration -######################################## - -#[tmc2130 stepper_x] -#cs_pin: PC4 -#spi_bus: spi1 -##diag1_pin: PG6 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2130 stepper_y] -#cs_pin: PD11 -#spi_bus: spi1 -##diag1_pin: PG9 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2130 stepper_z] -#cs_pin: PC6 -#spi_bus: spi1 -##diag1_pin: PG10 -#run_current: 0.650 -#stealthchop_threshold: 999999 - -#[tmc2130 stepper_] -#cs_pin: PC7 -#spi_bus: spi1 -##diag1_pin: PG11 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2130 extruder] -#cs_pin: PF2 -#spi_bus: spi1 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2130 extruder1] -#cs_pin: PE4 -#spi_bus: spi1 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2130 extruder2] -#cs_pin: PE1 -#spi_bus: spi1 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -#[tmc2130 extruder3] -#cs_pin: PD3 -#spi_bus: spi1 -#run_current: 0.800 -#stealthchop_threshold: 999999 - -[board_pins] -aliases: - # EXP1 header - EXP1_1=PE8, EXP1_2=PE7, - EXP1_3=PE9, EXP1_4=PE10, - EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side - EXP1_7=PE14, EXP1_8=PE15, - EXP1_9=, EXP1_10=<5V>, - - # EXP2 header - EXP2_1=PA6, EXP2_2=PA5, - EXP2_3=PB1, EXP2_4=PA4, - EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side - EXP2_7=PC15, EXP2_8=, - EXP2_9=, EXP2_10=PC5 - -# See the sample-lcd.cfg file for definitions of common LCD displays. - -# A [probe] section can be defined instead with a pin: setting identical -# to the sensor_pin: for a bltouch -#[bltouch] -#sensor_pin: PB7 -#control_pin: PB6 -#z_offset: 0 - -#[neopixel my_neopixel] -#pin: PB0 diff --git a/test/klippy/printers.test b/test/klippy/printers.test index 8038ad4c..ddb94ed2 100644 --- a/test/klippy/printers.test +++ b/test/klippy/printers.test @@ -227,9 +227,13 @@ CONFIG ../../config/generic-th3d-ezboard-v2.0.cfg CONFIG ../../config/printer-biqu-b1-se-plus-2022.cfg CONFIG ../../config/printer-prusa-mini-plus-2020.cfg +# Printers using the stm32f429 +DICTIONARY stm32f429.dict +CONFIG ../../config/generic-bigtreetech-octopus-v1.1.cfg + # Printers using the stm32f446 DICTIONARY stm32f446.dict -CONFIG ../../config/generic-bigtreetech-octopus.cfg +CONFIG ../../config/generic-bigtreetech-octopus-pro-v1.0.cfg CONFIG ../../config/generic-fysetc-s6.cfg CONFIG ../../config/generic-fysetc-s6-v2.cfg CONFIG ../../config/generic-fysetc-spider.cfg -- cgit v1.2.3-70-g09d2