diff options
Diffstat (limited to 'lib/hal-stm32f1/source/stm32f1xx_hal_adc.c')
| -rw-r--r-- | lib/hal-stm32f1/source/stm32f1xx_hal_adc.c | 2112 |
1 files changed, 2112 insertions, 0 deletions
diff --git a/lib/hal-stm32f1/source/stm32f1xx_hal_adc.c b/lib/hal-stm32f1/source/stm32f1xx_hal_adc.c new file mode 100644 index 00000000..b72327d8 --- /dev/null +++ b/lib/hal-stm32f1/source/stm32f1xx_hal_adc.c @@ -0,0 +1,2112 @@ +/**
+ ******************************************************************************
+ * @file stm32f1xx_hal_adc.c
+ * @author MCD Application Team
+ * @version V1.1.1
+ * @date 12-May-2017
+ * @brief This file provides firmware functions to manage the following
+ * functionalities of the Analog to Digital Convertor (ADC)
+ * peripheral:
+ * + Initialization and de-initialization functions
+ * ++ Initialization and Configuration of ADC
+ * + Operation functions
+ * ++ Start, stop, get result of conversions of regular
+ * group, using 3 possible modes: polling, interruption or DMA.
+ * + Control functions
+ * ++ Channels configuration on regular group
+ * ++ Channels configuration on injected group
+ * ++ Analog Watchdog configuration
+ * + State functions
+ * ++ ADC state machine management
+ * ++ Interrupts and flags management
+ * Other functions (extended functions) are available in file
+ * "stm32f1xx_hal_adc_ex.c".
+ *
+ @verbatim
+ ==============================================================================
+ ##### ADC peripheral features #####
+ ==============================================================================
+ [..]
+ (+) 12-bit resolution
+
+ (+) Interrupt generation at the end of regular conversion, end of injected
+ conversion, and in case of analog watchdog or overrun events.
+
+ (+) Single and continuous conversion modes.
+
+ (+) Scan mode for conversion of several channels sequentially.
+
+ (+) Data alignment with in-built data coherency.
+
+ (+) Programmable sampling time (channel wise)
+
+ (+) ADC conversion of regular group and injected group.
+
+ (+) External trigger (timer or EXTI)
+ for both regular and injected groups.
+
+ (+) DMA request generation for transfer of conversions data of regular group.
+
+ (+) Multimode Dual mode (available on devices with 2 ADCs or more).
+
+ (+) Configurable DMA data storage in Multimode Dual mode (available on devices
+ with 2 DCs or more).
+
+ (+) Configurable delay between conversions in Dual interleaved mode (available
+ on devices with 2 DCs or more).
+
+ (+) ADC calibration
+
+ (+) ADC supply requirements: 2.4 V to 3.6 V at full speed and down to 1.8 V at
+ slower speed.
+
+ (+) ADC input range: from Vref- (connected to Vssa) to Vref+ (connected to
+ Vdda or to an external voltage reference).
+
+
+ ##### How to use this driver #####
+ ==============================================================================
+ [..]
+
+ *** Configuration of top level parameters related to ADC ***
+ ============================================================
+ [..]
+
+ (#) Enable the ADC interface
+ (++) As prerequisite, ADC clock must be configured at RCC top level.
+ Caution: On STM32F1, ADC clock frequency max is 14MHz (refer
+ to device datasheet).
+ Therefore, ADC clock prescaler must be configured in
+ function of ADC clock source frequency to remain below
+ this maximum frequency.
+ (++) One clock setting is mandatory:
+ ADC clock (core clock, also possibly conversion clock).
+ (+++) Example:
+ Into HAL_ADC_MspInit() (recommended code location) or with
+ other device clock parameters configuration:
+ (+++) RCC_PeriphCLKInitTypeDef PeriphClkInit;
+ (+++) __ADC1_CLK_ENABLE();
+ (+++) PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC;
+ (+++) PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV2;
+ (+++) HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+
+ (#) ADC pins configuration
+ (++) Enable the clock for the ADC GPIOs
+ using macro __HAL_RCC_GPIOx_CLK_ENABLE()
+ (++) Configure these ADC pins in analog mode
+ using function HAL_GPIO_Init()
+
+ (#) Optionally, in case of usage of ADC with interruptions:
+ (++) Configure the NVIC for ADC
+ using function HAL_NVIC_EnableIRQ(ADCx_IRQn)
+ (++) Insert the ADC interruption handler function HAL_ADC_IRQHandler()
+ into the function of corresponding ADC interruption vector
+ ADCx_IRQHandler().
+
+ (#) Optionally, in case of usage of DMA:
+ (++) Configure the DMA (DMA channel, mode normal or circular, ...)
+ using function HAL_DMA_Init().
+ (++) Configure the NVIC for DMA
+ using function HAL_NVIC_EnableIRQ(DMAx_Channelx_IRQn)
+ (++) Insert the ADC interruption handler function HAL_ADC_IRQHandler()
+ into the function of corresponding DMA interruption vector
+ DMAx_Channelx_IRQHandler().
+
+ *** Configuration of ADC, groups regular/injected, channels parameters ***
+ ==========================================================================
+ [..]
+
+ (#) Configure the ADC parameters (resolution, data alignment, ...)
+ and regular group parameters (conversion trigger, sequencer, ...)
+ using function HAL_ADC_Init().
+
+ (#) Configure the channels for regular group parameters (channel number,
+ channel rank into sequencer, ..., into regular group)
+ using function HAL_ADC_ConfigChannel().
+
+ (#) Optionally, configure the injected group parameters (conversion trigger,
+ sequencer, ..., of injected group)
+ and the channels for injected group parameters (channel number,
+ channel rank into sequencer, ..., into injected group)
+ using function HAL_ADCEx_InjectedConfigChannel().
+
+ (#) Optionally, configure the analog watchdog parameters (channels
+ monitored, thresholds, ...)
+ using function HAL_ADC_AnalogWDGConfig().
+
+ (#) Optionally, for devices with several ADC instances: configure the
+ multimode parameters
+ using function HAL_ADCEx_MultiModeConfigChannel().
+
+ *** Execution of ADC conversions ***
+ ====================================
+ [..]
+
+ (#) Optionally, perform an automatic ADC calibration to improve the
+ conversion accuracy
+ using function HAL_ADCEx_Calibration_Start().
+
+ (#) ADC driver can be used among three modes: polling, interruption,
+ transfer by DMA.
+
+ (++) ADC conversion by polling:
+ (+++) Activate the ADC peripheral and start conversions
+ using function HAL_ADC_Start()
+ (+++) Wait for ADC conversion completion
+ using function HAL_ADC_PollForConversion()
+ (or for injected group: HAL_ADCEx_InjectedPollForConversion() )
+ (+++) Retrieve conversion results
+ using function HAL_ADC_GetValue()
+ (or for injected group: HAL_ADCEx_InjectedGetValue() )
+ (+++) Stop conversion and disable the ADC peripheral
+ using function HAL_ADC_Stop()
+
+ (++) ADC conversion by interruption:
+ (+++) Activate the ADC peripheral and start conversions
+ using function HAL_ADC_Start_IT()
+ (+++) Wait for ADC conversion completion by call of function
+ HAL_ADC_ConvCpltCallback()
+ (this function must be implemented in user program)
+ (or for injected group: HAL_ADCEx_InjectedConvCpltCallback() )
+ (+++) Retrieve conversion results
+ using function HAL_ADC_GetValue()
+ (or for injected group: HAL_ADCEx_InjectedGetValue() )
+ (+++) Stop conversion and disable the ADC peripheral
+ using function HAL_ADC_Stop_IT()
+
+ (++) ADC conversion with transfer by DMA:
+ (+++) Activate the ADC peripheral and start conversions
+ using function HAL_ADC_Start_DMA()
+ (+++) Wait for ADC conversion completion by call of function
+ HAL_ADC_ConvCpltCallback() or HAL_ADC_ConvHalfCpltCallback()
+ (these functions must be implemented in user program)
+ (+++) Conversion results are automatically transferred by DMA into
+ destination variable address.
+ (+++) Stop conversion and disable the ADC peripheral
+ using function HAL_ADC_Stop_DMA()
+
+ (++) For devices with several ADCs: ADC multimode conversion
+ with transfer by DMA:
+ (+++) Activate the ADC peripheral (slave) and start conversions
+ using function HAL_ADC_Start()
+ (+++) Activate the ADC peripheral (master) and start conversions
+ using function HAL_ADCEx_MultiModeStart_DMA()
+ (+++) Wait for ADC conversion completion by call of function
+ HAL_ADC_ConvCpltCallback() or HAL_ADC_ConvHalfCpltCallback()
+ (these functions must be implemented in user program)
+ (+++) Conversion results are automatically transferred by DMA into
+ destination variable address.
+ (+++) Stop conversion and disable the ADC peripheral (master)
+ using function HAL_ADCEx_MultiModeStop_DMA()
+ (+++) Stop conversion and disable the ADC peripheral (slave)
+ using function HAL_ADC_Stop_IT()
+
+ [..]
+
+ (@) Callback functions must be implemented in user program:
+ (+@) HAL_ADC_ErrorCallback()
+ (+@) HAL_ADC_LevelOutOfWindowCallback() (callback of analog watchdog)
+ (+@) HAL_ADC_ConvCpltCallback()
+ (+@) HAL_ADC_ConvHalfCpltCallback
+ (+@) HAL_ADCEx_InjectedConvCpltCallback()
+
+ *** Deinitialization of ADC ***
+ ============================================================
+ [..]
+
+ (#) Disable the ADC interface
+ (++) ADC clock can be hard reset and disabled at RCC top level.
+ (++) Hard reset of ADC peripherals
+ using macro __ADCx_FORCE_RESET(), __ADCx_RELEASE_RESET().
+ (++) ADC clock disable
+ using the equivalent macro/functions as configuration step.
+ (+++) Example:
+ Into HAL_ADC_MspDeInit() (recommended code location) or with
+ other device clock parameters configuration:
+ (+++) PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC
+ (+++) PeriphClkInit.AdcClockSelection = RCC_ADCPLLCLK2_OFF
+ (+++) HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit)
+
+ (#) ADC pins configuration
+ (++) Disable the clock for the ADC GPIOs
+ using macro __HAL_RCC_GPIOx_CLK_DISABLE()
+
+ (#) Optionally, in case of usage of ADC with interruptions:
+ (++) Disable the NVIC for ADC
+ using function HAL_NVIC_EnableIRQ(ADCx_IRQn)
+
+ (#) Optionally, in case of usage of DMA:
+ (++) Deinitialize the DMA
+ using function HAL_DMA_Init().
+ (++) Disable the NVIC for DMA
+ using function HAL_NVIC_EnableIRQ(DMAx_Channelx_IRQn)
+
+ [..]
+
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup ADC ADC
+ * @brief ADC HAL module driver
+ * @{
+ */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @defgroup ADC_Private_Constants ADC Private Constants
+ * @{
+ */
+
+ /* Timeout values for ADC enable and disable settling time. */
+ /* Values defined to be higher than worst cases: low clocks freq, */
+ /* maximum prescaler. */
+ /* Ex of profile low frequency : Clock source at 0.1 MHz, ADC clock */
+ /* prescaler 4, sampling time 12.5 ADC clock cycles, resolution 12 bits. */
+ /* Unit: ms */
+ #define ADC_ENABLE_TIMEOUT 2U
+ #define ADC_DISABLE_TIMEOUT 2U
+
+ /* Delay for ADC stabilization time. */
+ /* Maximum delay is 1us (refer to device datasheet, parameter tSTAB). */
+ /* Unit: us */
+ #define ADC_STAB_DELAY_US 1U
+
+ /* Delay for temperature sensor stabilization time. */
+ /* Maximum delay is 10us (refer to device datasheet, parameter tSTART). */
+ /* Unit: us */
+ #define ADC_TEMPSENSOR_DELAY_US 10U
+
+/**
+ * @}
+ */
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/** @defgroup ADC_Private_Functions ADC Private Functions
+ * @{
+ */
+/**
+ * @}
+ */
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @defgroup ADC_Exported_Functions ADC Exported Functions
+ * @{
+ */
+
+/** @defgroup ADC_Exported_Functions_Group1 Initialization/de-initialization functions
+ * @brief Initialization and Configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Initialization and de-initialization functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+ (+) Initialize and configure the ADC.
+ (+) De-initialize the ADC.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Initializes the ADC peripheral and regular group according to
+ * parameters specified in structure "ADC_InitTypeDef".
+ * @note As prerequisite, ADC clock must be configured at RCC top level
+ * (clock source APB2).
+ * See commented example code below that can be copied and uncommented
+ * into HAL_ADC_MspInit().
+ * @note Possibility to update parameters on the fly:
+ * This function initializes the ADC MSP (HAL_ADC_MspInit()) only when
+ * coming from ADC state reset. Following calls to this function can
+ * be used to reconfigure some parameters of ADC_InitTypeDef
+ * structure on the fly, without modifying MSP configuration. If ADC
+ * MSP has to be modified again, HAL_ADC_DeInit() must be called
+ * before HAL_ADC_Init().
+ * The setting of these parameters is conditioned to ADC state.
+ * For parameters constraints, see comments of structure
+ * "ADC_InitTypeDef".
+ * @note This function configures the ADC within 2 scopes: scope of entire
+ * ADC and scope of regular group. For parameters details, see comments
+ * of structure "ADC_InitTypeDef".
+ * @param hadc: ADC handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_Init(ADC_HandleTypeDef* hadc)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+ uint32_t tmp_cr1 = 0U;
+ uint32_t tmp_cr2 = 0U;
+ uint32_t tmp_sqr1 = 0U;
+
+ /* Check ADC handle */
+ if(hadc == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+ assert_param(IS_ADC_DATA_ALIGN(hadc->Init.DataAlign));
+ assert_param(IS_ADC_SCAN_MODE(hadc->Init.ScanConvMode));
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
+ assert_param(IS_ADC_EXTTRIG(hadc->Init.ExternalTrigConv));
+
+ if(hadc->Init.ScanConvMode != ADC_SCAN_DISABLE)
+ {
+ assert_param(IS_ADC_REGULAR_NB_CONV(hadc->Init.NbrOfConversion));
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.DiscontinuousConvMode));
+ if(hadc->Init.DiscontinuousConvMode != DISABLE)
+ {
+ assert_param(IS_ADC_REGULAR_DISCONT_NUMBER(hadc->Init.NbrOfDiscConversion));
+ }
+ }
+
+ /* As prerequisite, into HAL_ADC_MspInit(), ADC clock must be configured */
+ /* at RCC top level. */
+ /* Refer to header of this file for more details on clock enabling */
+ /* procedure. */
+
+ /* Actions performed only if ADC is coming from state reset: */
+ /* - Initialization of ADC MSP */
+ if (hadc->State == HAL_ADC_STATE_RESET)
+ {
+ /* Initialize ADC error code */
+ ADC_CLEAR_ERRORCODE(hadc);
+
+ /* Allocate lock resource and initialize it */
+ hadc->Lock = HAL_UNLOCKED;
+
+ /* Init the low level hardware */
+ HAL_ADC_MspInit(hadc);
+ }
+
+ /* Stop potential conversion on going, on regular and injected groups */
+ /* Disable ADC peripheral */
+ /* Note: In case of ADC already enabled, precaution to not launch an */
+ /* unwanted conversion while modifying register CR2 by writing 1 to */
+ /* bit ADON. */
+ tmp_hal_status = ADC_ConversionStop_Disable(hadc);
+
+
+ /* Configuration of ADC parameters if previous preliminary actions are */
+ /* correctly completed. */
+ if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL) &&
+ (tmp_hal_status == HAL_OK) )
+ {
+ /* Set ADC state */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_REG_BUSY | HAL_ADC_STATE_INJ_BUSY,
+ HAL_ADC_STATE_BUSY_INTERNAL);
+
+ /* Set ADC parameters */
+
+ /* Configuration of ADC: */
+ /* - data alignment */
+ /* - external trigger to start conversion */
+ /* - external trigger polarity (always set to 1, because needed for all */
+ /* triggers: external trigger of SW start) */
+ /* - continuous conversion mode */
+ /* Note: External trigger polarity (ADC_CR2_EXTTRIG) is set into */
+ /* HAL_ADC_Start_xxx functions because if set in this function, */
+ /* a conversion on injected group would start a conversion also on */
+ /* regular group after ADC enabling. */
+ tmp_cr2 |= (hadc->Init.DataAlign |
+ ADC_CFGR_EXTSEL(hadc, hadc->Init.ExternalTrigConv) |
+ ADC_CR2_CONTINUOUS(hadc->Init.ContinuousConvMode) );
+
+ /* Configuration of ADC: */
+ /* - scan mode */
+ /* - discontinuous mode disable/enable */
+ /* - discontinuous mode number of conversions */
+ tmp_cr1 |= (ADC_CR1_SCAN_SET(hadc->Init.ScanConvMode));
+
+ /* Enable discontinuous mode only if continuous mode is disabled */
+ /* Note: If parameter "Init.ScanConvMode" is set to disable, parameter */
+ /* discontinuous is set anyway, but will have no effect on ADC HW. */
+ if (hadc->Init.DiscontinuousConvMode == ENABLE)
+ {
+ if (hadc->Init.ContinuousConvMode == DISABLE)
+ {
+ /* Enable the selected ADC regular discontinuous mode */
+ /* Set the number of channels to be converted in discontinuous mode */
+ SET_BIT(tmp_cr1, ADC_CR1_DISCEN |
+ ADC_CR1_DISCONTINUOUS_NUM(hadc->Init.NbrOfDiscConversion) );
+ }
+ else
+ {
+ /* ADC regular group settings continuous and sequencer discontinuous*/
+ /* cannot be enabled simultaneously. */
+
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
+
+ /* Set ADC error code to ADC IP internal error */
+ SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
+ }
+ }
+
+ /* Update ADC configuration register CR1 with previous settings */
+ MODIFY_REG(hadc->Instance->CR1,
+ ADC_CR1_SCAN |
+ ADC_CR1_DISCEN |
+ ADC_CR1_DISCNUM ,
+ tmp_cr1 );
+
+ /* Update ADC configuration register CR2 with previous settings */
+ MODIFY_REG(hadc->Instance->CR2,
+ ADC_CR2_ALIGN |
+ ADC_CR2_EXTSEL |
+ ADC_CR2_EXTTRIG |
+ ADC_CR2_CONT ,
+ tmp_cr2 );
+
+ /* Configuration of regular group sequencer: */
+ /* - if scan mode is disabled, regular channels sequence length is set to */
+ /* 0x00: 1 channel converted (channel on regular rank 1) */
+ /* Parameter "NbrOfConversion" is discarded. */
+ /* Note: Scan mode is present by hardware on this device and, if */
+ /* disabled, discards automatically nb of conversions. Anyway, nb of */
+ /* conversions is forced to 0x00 for alignment over all STM32 devices. */
+ /* - if scan mode is enabled, regular channels sequence length is set to */
+ /* parameter "NbrOfConversion" */
+ if (ADC_CR1_SCAN_SET(hadc->Init.ScanConvMode) == ADC_SCAN_ENABLE)
+ {
+ tmp_sqr1 = ADC_SQR1_L_SHIFT(hadc->Init.NbrOfConversion);
+ }
+
+ MODIFY_REG(hadc->Instance->SQR1,
+ ADC_SQR1_L ,
+ tmp_sqr1 );
+
+ /* Check back that ADC registers have effectively been configured to */
+ /* ensure of no potential problem of ADC core IP clocking. */
+ /* Check through register CR2 (excluding bits set in other functions: */
+ /* execution control bits (ADON, JSWSTART, SWSTART), regular group bits */
+ /* (DMA), injected group bits (JEXTTRIG and JEXTSEL), channel internal */
+ /* measurement path bit (TSVREFE). */
+ if (READ_BIT(hadc->Instance->CR2, ~(ADC_CR2_ADON | ADC_CR2_DMA |
+ ADC_CR2_SWSTART | ADC_CR2_JSWSTART |
+ ADC_CR2_JEXTTRIG | ADC_CR2_JEXTSEL |
+ ADC_CR2_TSVREFE ))
+ == tmp_cr2)
+ {
+ /* Set ADC error code to none */
+ ADC_CLEAR_ERRORCODE(hadc);
+
+ /* Set the ADC state */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_BUSY_INTERNAL,
+ HAL_ADC_STATE_READY);
+ }
+ else
+ {
+ /* Update ADC state machine to error */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_BUSY_INTERNAL,
+ HAL_ADC_STATE_ERROR_INTERNAL);
+
+ /* Set ADC error code to ADC IP internal error */
+ SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
+
+ tmp_hal_status = HAL_ERROR;
+ }
+
+ }
+ else
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
+
+ tmp_hal_status = HAL_ERROR;
+ }
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Deinitialize the ADC peripheral registers to their default reset
+ * values, with deinitialization of the ADC MSP.
+ * If needed, the example code can be copied and uncommented into
+ * function HAL_ADC_MspDeInit().
+ * @param hadc: ADC handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_DeInit(ADC_HandleTypeDef* hadc)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+
+ /* Check ADC handle */
+ if(hadc == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+
+ /* Set ADC state */
+ SET_BIT(hadc->State, HAL_ADC_STATE_BUSY_INTERNAL);
+
+ /* Stop potential conversion on going, on regular and injected groups */
+ /* Disable ADC peripheral */
+ tmp_hal_status = ADC_ConversionStop_Disable(hadc);
+
+
+ /* Configuration of ADC parameters if previous preliminary actions are */
+ /* correctly completed. */
+ if (tmp_hal_status == HAL_OK)
+ {
+ /* ========== Reset ADC registers ========== */
+
+
+
+
+ /* Reset register SR */
+ __HAL_ADC_CLEAR_FLAG(hadc, (ADC_FLAG_AWD | ADC_FLAG_JEOC | ADC_FLAG_EOC |
+ ADC_FLAG_JSTRT | ADC_FLAG_STRT));
+
+ /* Reset register CR1 */
+ CLEAR_BIT(hadc->Instance->CR1, (ADC_CR1_AWDEN | ADC_CR1_JAWDEN | ADC_CR1_DISCNUM |
+ ADC_CR1_JDISCEN | ADC_CR1_DISCEN | ADC_CR1_JAUTO |
+ ADC_CR1_AWDSGL | ADC_CR1_SCAN | ADC_CR1_JEOCIE |
+ ADC_CR1_AWDIE | ADC_CR1_EOCIE | ADC_CR1_AWDCH ));
+
+ /* Reset register CR2 */
+ CLEAR_BIT(hadc->Instance->CR2, (ADC_CR2_TSVREFE | ADC_CR2_SWSTART | ADC_CR2_JSWSTART |
+ ADC_CR2_EXTTRIG | ADC_CR2_EXTSEL | ADC_CR2_JEXTTRIG |
+ ADC_CR2_JEXTSEL | ADC_CR2_ALIGN | ADC_CR2_DMA |
+ ADC_CR2_RSTCAL | ADC_CR2_CAL | ADC_CR2_CONT |
+ ADC_CR2_ADON ));
+
+ /* Reset register SMPR1 */
+ CLEAR_BIT(hadc->Instance->SMPR1, (ADC_SMPR1_SMP17 | ADC_SMPR1_SMP16 | ADC_SMPR1_SMP15 |
+ ADC_SMPR1_SMP14 | ADC_SMPR1_SMP13 | ADC_SMPR1_SMP12 |
+ ADC_SMPR1_SMP11 | ADC_SMPR1_SMP10 ));
+
+ /* Reset register SMPR2 */
+ CLEAR_BIT(hadc->Instance->SMPR2, (ADC_SMPR2_SMP9 | ADC_SMPR2_SMP8 | ADC_SMPR2_SMP7 |
+ ADC_SMPR2_SMP6 | ADC_SMPR2_SMP5 | ADC_SMPR2_SMP4 |
+ ADC_SMPR2_SMP3 | ADC_SMPR2_SMP2 | ADC_SMPR2_SMP1 |
+ ADC_SMPR2_SMP0 ));
+
+ /* Reset register JOFR1 */
+ CLEAR_BIT(hadc->Instance->JOFR1, ADC_JOFR1_JOFFSET1);
+ /* Reset register JOFR2 */
+ CLEAR_BIT(hadc->Instance->JOFR2, ADC_JOFR2_JOFFSET2);
+ /* Reset register JOFR3 */
+ CLEAR_BIT(hadc->Instance->JOFR3, ADC_JOFR3_JOFFSET3);
+ /* Reset register JOFR4 */
+ CLEAR_BIT(hadc->Instance->JOFR4, ADC_JOFR4_JOFFSET4);
+
+ /* Reset register HTR */
+ CLEAR_BIT(hadc->Instance->HTR, ADC_HTR_HT);
+ /* Reset register LTR */
+ CLEAR_BIT(hadc->Instance->LTR, ADC_LTR_LT);
+
+ /* Reset register SQR1 */
+ CLEAR_BIT(hadc->Instance->SQR1, ADC_SQR1_L |
+ ADC_SQR1_SQ16 | ADC_SQR1_SQ15 |
+ ADC_SQR1_SQ14 | ADC_SQR1_SQ13 );
+
+ /* Reset register SQR1 */
+ CLEAR_BIT(hadc->Instance->SQR1, ADC_SQR1_L |
+ ADC_SQR1_SQ16 | ADC_SQR1_SQ15 |
+ ADC_SQR1_SQ14 | ADC_SQR1_SQ13 );
+
+ /* Reset register SQR2 */
+ CLEAR_BIT(hadc->Instance->SQR2, ADC_SQR2_SQ12 | ADC_SQR2_SQ11 | ADC_SQR2_SQ10 |
+ ADC_SQR2_SQ9 | ADC_SQR2_SQ8 | ADC_SQR2_SQ7 );
+
+ /* Reset register SQR3 */
+ CLEAR_BIT(hadc->Instance->SQR3, ADC_SQR3_SQ6 | ADC_SQR3_SQ5 | ADC_SQR3_SQ4 |
+ ADC_SQR3_SQ3 | ADC_SQR3_SQ2 | ADC_SQR3_SQ1 );
+
+ /* Reset register JSQR */
+ CLEAR_BIT(hadc->Instance->JSQR, ADC_JSQR_JL |
+ ADC_JSQR_JSQ4 | ADC_JSQR_JSQ3 |
+ ADC_JSQR_JSQ2 | ADC_JSQR_JSQ1 );
+
+ /* Reset register JSQR */
+ CLEAR_BIT(hadc->Instance->JSQR, ADC_JSQR_JL |
+ ADC_JSQR_JSQ4 | ADC_JSQR_JSQ3 |
+ ADC_JSQR_JSQ2 | ADC_JSQR_JSQ1 );
+
+ /* Reset register DR */
+ /* bits in access mode read only, no direct reset applicable*/
+
+ /* Reset registers JDR1, JDR2, JDR3, JDR4 */
+ /* bits in access mode read only, no direct reset applicable*/
+
+ /* ========== Hard reset ADC peripheral ========== */
+ /* Performs a global reset of the entire ADC peripheral: ADC state is */
+ /* forced to a similar state after device power-on. */
+ /* If needed, copy-paste and uncomment the following reset code into */
+ /* function "void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)": */
+ /* */
+ /* __HAL_RCC_ADC1_FORCE_RESET() */
+ /* __HAL_RCC_ADC1_RELEASE_RESET() */
+
+ /* DeInit the low level hardware */
+ HAL_ADC_MspDeInit(hadc);
+
+ /* Set ADC error code to none */
+ ADC_CLEAR_ERRORCODE(hadc);
+
+ /* Set ADC state */
+ hadc->State = HAL_ADC_STATE_RESET;
+
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Initializes the ADC MSP.
+ * @param hadc: ADC handle
+ * @retval None
+ */
+__weak void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hadc);
+ /* NOTE : This function should not be modified. When the callback is needed,
+ function HAL_ADC_MspInit must be implemented in the user file.
+ */
+}
+
+/**
+ * @brief DeInitializes the ADC MSP.
+ * @param hadc: ADC handle
+ * @retval None
+ */
+__weak void HAL_ADC_MspDeInit(ADC_HandleTypeDef* hadc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hadc);
+ /* NOTE : This function should not be modified. When the callback is needed,
+ function HAL_ADC_MspDeInit must be implemented in the user file.
+ */
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup ADC_Exported_Functions_Group2 IO operation functions
+ * @brief Input and Output operation functions
+ *
+@verbatim
+ ===============================================================================
+ ##### IO operation functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+ (+) Start conversion of regular group.
+ (+) Stop conversion of regular group.
+ (+) Poll for conversion complete on regular group.
+ (+) Poll for conversion event.
+ (+) Get result of regular channel conversion.
+ (+) Start conversion of regular group and enable interruptions.
+ (+) Stop conversion of regular group and disable interruptions.
+ (+) Handle ADC interrupt request
+ (+) Start conversion of regular group and enable DMA transfer.
+ (+) Stop conversion of regular group and disable ADC DMA transfer.
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enables ADC, starts conversion of regular group.
+ * Interruptions enabled in this function: None.
+ * @param hadc: ADC handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_Start(ADC_HandleTypeDef* hadc)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Enable the ADC peripheral */
+ tmp_hal_status = ADC_Enable(hadc);
+
+ /* Start conversion if ADC is effectively enabled */
+ if (tmp_hal_status == HAL_OK)
+ {
+ /* Set ADC state */
+ /* - Clear state bitfield related to regular group conversion results */
+ /* - Set state bitfield related to regular operation */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_READY | HAL_ADC_STATE_REG_EOC,
+ HAL_ADC_STATE_REG_BUSY);
+
+ /* Set group injected state (from auto-injection) and multimode state */
+ /* for all cases of multimode: independent mode, multimode ADC master */
+ /* or multimode ADC slave (for devices with several ADCs): */
+ if (ADC_NONMULTIMODE_OR_MULTIMODEMASTER(hadc))
+ {
+ /* Set ADC state (ADC independent or master) */
+ CLEAR_BIT(hadc->State, HAL_ADC_STATE_MULTIMODE_SLAVE);
+
+ /* If conversions on group regular are also triggering group injected, */
+ /* update ADC state. */
+ if (READ_BIT(hadc->Instance->CR1, ADC_CR1_JAUTO) != RESET)
+ {
+ ADC_STATE_CLR_SET(hadc->State, HAL_ADC_STATE_INJ_EOC, HAL_ADC_STATE_INJ_BUSY);
+ }
+ }
+ else
+ {
+ /* Set ADC state (ADC slave) */
+ SET_BIT(hadc->State, HAL_ADC_STATE_MULTIMODE_SLAVE);
+
+ /* If conversions on group regular are also triggering group injected, */
+ /* update ADC state. */
+ if (ADC_MULTIMODE_AUTO_INJECTED(hadc))
+ {
+ ADC_STATE_CLR_SET(hadc->State, HAL_ADC_STATE_INJ_EOC, HAL_ADC_STATE_INJ_BUSY);
+ }
+ }
+
+ /* State machine update: Check if an injected conversion is ongoing */
+ if (HAL_IS_BIT_SET(hadc->State, HAL_ADC_STATE_INJ_BUSY))
+ {
+ /* Reset ADC error code fields related to conversions on group regular */
+ CLEAR_BIT(hadc->ErrorCode, (HAL_ADC_ERROR_OVR | HAL_ADC_ERROR_DMA));
+ }
+ else
+ {
+ /* Reset ADC all error code fields */
+ ADC_CLEAR_ERRORCODE(hadc);
+ }
+
+ /* Process unlocked */
+ /* Unlock before starting ADC conversions: in case of potential */
+ /* interruption, to let the process to ADC IRQ Handler. */
+ __HAL_UNLOCK(hadc);
+
+ /* Clear regular group conversion flag */
+ /* (To ensure of no unknown state from potential previous ADC operations) */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_EOC);
+
+ /* Enable conversion of regular group. */
+ /* If software start has been selected, conversion starts immediately. */
+ /* If external trigger has been selected, conversion will start at next */
+ /* trigger event. */
+ /* Case of multimode enabled: */
+ /* - if ADC is slave, ADC is enabled only (conversion is not started). */
+ /* - if ADC is master, ADC is enabled and conversion is started. */
+ /* If ADC is master, ADC is enabled and conversion is started. */
+ /* Note: Alternate trigger for single conversion could be to force an */
+ /* additional set of bit ADON "hadc->Instance->CR2 |= ADC_CR2_ADON;"*/
+ if (ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
+ ADC_NONMULTIMODE_OR_MULTIMODEMASTER(hadc) )
+ {
+ /* Start ADC conversion on regular group with SW start */
+ SET_BIT(hadc->Instance->CR2, (ADC_CR2_SWSTART | ADC_CR2_EXTTRIG));
+ }
+ else
+ {
+ /* Start ADC conversion on regular group with external trigger */
+ SET_BIT(hadc->Instance->CR2, ADC_CR2_EXTTRIG);
+ }
+ }
+ else
+ {
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+ }
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Stop ADC conversion of regular group (and injected channels in
+ * case of auto_injection mode), disable ADC peripheral.
+ * @note: ADC peripheral disable is forcing stop of potential
+ * conversion on injected group. If injected group is under use, it
+ * should be preliminarily stopped using HAL_ADCEx_InjectedStop function.
+ * @param hadc: ADC handle
+ * @retval HAL status.
+ */
+HAL_StatusTypeDef HAL_ADC_Stop(ADC_HandleTypeDef* hadc)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Stop potential conversion on going, on regular and injected groups */
+ /* Disable ADC peripheral */
+ tmp_hal_status = ADC_ConversionStop_Disable(hadc);
+
+ /* Check if ADC is effectively disabled */
+ if (tmp_hal_status == HAL_OK)
+ {
+ /* Set ADC state */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_REG_BUSY | HAL_ADC_STATE_INJ_BUSY,
+ HAL_ADC_STATE_READY);
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Wait for regular group conversion to be completed.
+ * @note This function cannot be used in a particular setup: ADC configured
+ * in DMA mode.
+ * In this case, DMA resets the flag EOC and polling cannot be
+ * performed on each conversion.
+ * @note On STM32F1 devices, limitation in case of sequencer enabled
+ * (several ranks selected): polling cannot be done on each
+ * conversion inside the sequence. In this case, polling is replaced by
+ * wait for maximum conversion time.
+ * @param hadc: ADC handle
+ * @param Timeout: Timeout value in millisecond.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_PollForConversion(ADC_HandleTypeDef* hadc, uint32_t Timeout)
+{
+ uint32_t tickstart = 0U;
+
+ /* Variables for polling in case of scan mode enabled and polling for each */
+ /* conversion. */
+ __IO uint32_t Conversion_Timeout_CPU_cycles = 0U;
+ uint32_t Conversion_Timeout_CPU_cycles_max = 0U;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+
+ /* Get tick count */
+ tickstart = HAL_GetTick();
+
+ /* Verification that ADC configuration is compliant with polling for */
+ /* each conversion: */
+ /* Particular case is ADC configured in DMA mode */
+ if (HAL_IS_BIT_SET(hadc->Instance->CR2, ADC_CR2_DMA))
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ return HAL_ERROR;
+ }
+
+ /* Polling for end of conversion: differentiation if single/sequence */
+ /* conversion. */
+ /* - If single conversion for regular group (Scan mode disabled or enabled */
+ /* with NbrOfConversion =1), flag EOC is used to determine the */
+ /* conversion completion. */
+ /* - If sequence conversion for regular group (scan mode enabled and */
+ /* NbrOfConversion >=2), flag EOC is set only at the end of the */
+ /* sequence. */
+ /* To poll for each conversion, the maximum conversion time is computed */
+ /* from ADC conversion time (selected sampling time + conversion time of */
+ /* 12.5 ADC clock cycles) and APB2/ADC clock prescalers (depending on */
+ /* settings, conversion time range can be from 28 to 32256 CPU cycles). */
+ /* As flag EOC is not set after each conversion, no timeout status can */
+ /* be set. */
+ if (HAL_IS_BIT_CLR(hadc->Instance->CR1, ADC_CR1_SCAN) &&
+ HAL_IS_BIT_CLR(hadc->Instance->SQR1, ADC_SQR1_L) )
+ {
+ /* Wait until End of Conversion flag is raised */
+ while(HAL_IS_BIT_CLR(hadc->Instance->SR, ADC_FLAG_EOC))
+ {
+ /* Check if timeout is disabled (set to infinite wait) */
+ if(Timeout != HAL_MAX_DELAY)
+ {
+ if((Timeout == 0U) || ((HAL_GetTick() - tickstart ) > Timeout))
+ {
+ /* Update ADC state machine to timeout */
+ SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ else
+ {
+ /* Replace polling by wait for maximum conversion time */
+ /* - Computation of CPU clock cycles corresponding to ADC clock cycles */
+ /* and ADC maximum conversion cycles on all channels. */
+ /* - Wait for the expected ADC clock cycles delay */
+ Conversion_Timeout_CPU_cycles_max = ((SystemCoreClock
+ / HAL_RCCEx_GetPeriphCLKFreq(RCC_PERIPHCLK_ADC))
+ * ADC_CONVCYCLES_MAX_RANGE(hadc) );
+
+ while(Conversion_Timeout_CPU_cycles < Conversion_Timeout_CPU_cycles_max)
+ {
+ /* Check if timeout is disabled (set to infinite wait) */
+ if(Timeout != HAL_MAX_DELAY)
+ {
+ if((Timeout == 0U) || ((HAL_GetTick() - tickstart) > Timeout))
+ {
+ /* Update ADC state machine to timeout */
+ SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+ Conversion_Timeout_CPU_cycles ++;
+ }
+ }
+
+ /* Clear regular group conversion flag */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_STRT | ADC_FLAG_EOC);
+
+ /* Update ADC state machine */
+ SET_BIT(hadc->State, HAL_ADC_STATE_REG_EOC);
+
+ /* Determine whether any further conversion upcoming on group regular */
+ /* by external trigger, continuous mode or scan sequence on going. */
+ /* Note: On STM32F1 devices, in case of sequencer enabled */
+ /* (several ranks selected), end of conversion flag is raised */
+ /* at the end of the sequence. */
+ if(ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
+ (hadc->Init.ContinuousConvMode == DISABLE) )
+ {
+ /* Set ADC state */
+ CLEAR_BIT(hadc->State, HAL_ADC_STATE_REG_BUSY);
+
+ if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_INJ_BUSY))
+ {
+ SET_BIT(hadc->State, HAL_ADC_STATE_READY);
+ }
+ }
+
+ /* Return ADC state */
+ return HAL_OK;
+}
+
+/**
+ * @brief Poll for conversion event.
+ * @param hadc: ADC handle
+ * @param EventType: the ADC event type.
+ * This parameter can be one of the following values:
+ * @arg ADC_AWD_EVENT: ADC Analog watchdog event.
+ * @param Timeout: Timeout value in millisecond.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_PollForEvent(ADC_HandleTypeDef* hadc, uint32_t EventType, uint32_t Timeout)
+{
+ uint32_t tickstart = 0U;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+ assert_param(IS_ADC_EVENT_TYPE(EventType));
+
+ /* Get tick count */
+ tickstart = HAL_GetTick();
+
+ /* Check selected event flag */
+ while(__HAL_ADC_GET_FLAG(hadc, EventType) == RESET)
+ {
+ /* Check if timeout is disabled (set to infinite wait) */
+ if(Timeout != HAL_MAX_DELAY)
+ {
+ if((Timeout == 0U) || ((HAL_GetTick() - tickstart ) > Timeout))
+ {
+ /* Update ADC state machine to timeout */
+ SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ /* Analog watchdog (level out of window) event */
+ /* Set ADC state */
+ SET_BIT(hadc->State, HAL_ADC_STATE_AWD1);
+
+ /* Clear ADC analog watchdog flag */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_AWD);
+
+ /* Return ADC state */
+ return HAL_OK;
+}
+
+/**
+ * @brief Enables ADC, starts conversion of regular group with interruption.
+ * Interruptions enabled in this function:
+ * - EOC (end of conversion of regular group)
+ * Each of these interruptions has its dedicated callback function.
+ * @param hadc: ADC handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_Start_IT(ADC_HandleTypeDef* hadc)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Enable the ADC peripheral */
+ tmp_hal_status = ADC_Enable(hadc);
+
+ /* Start conversion if ADC is effectively enabled */
+ if (tmp_hal_status == HAL_OK)
+ {
+ /* Set ADC state */
+ /* - Clear state bitfield related to regular group conversion results */
+ /* - Set state bitfield related to regular operation */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_READY | HAL_ADC_STATE_REG_EOC | HAL_ADC_STATE_REG_OVR | HAL_ADC_STATE_REG_EOSMP,
+ HAL_ADC_STATE_REG_BUSY);
+
+ /* Set group injected state (from auto-injection) and multimode state */
+ /* for all cases of multimode: independent mode, multimode ADC master */
+ /* or multimode ADC slave (for devices with several ADCs): */
+ if (ADC_NONMULTIMODE_OR_MULTIMODEMASTER(hadc))
+ {
+ /* Set ADC state (ADC independent or master) */
+ CLEAR_BIT(hadc->State, HAL_ADC_STATE_MULTIMODE_SLAVE);
+
+ /* If conversions on group regular are also triggering group injected, */
+ /* update ADC state. */
+ if (READ_BIT(hadc->Instance->CR1, ADC_CR1_JAUTO) != RESET)
+ {
+ ADC_STATE_CLR_SET(hadc->State, HAL_ADC_STATE_INJ_EOC, HAL_ADC_STATE_INJ_BUSY);
+ }
+ }
+ else
+ {
+ /* Set ADC state (ADC slave) */
+ SET_BIT(hadc->State, HAL_ADC_STATE_MULTIMODE_SLAVE);
+
+ /* If conversions on group regular are also triggering group injected, */
+ /* update ADC state. */
+ if (ADC_MULTIMODE_AUTO_INJECTED(hadc))
+ {
+ ADC_STATE_CLR_SET(hadc->State, HAL_ADC_STATE_INJ_EOC, HAL_ADC_STATE_INJ_BUSY);
+ }
+ }
+
+ /* State machine update: Check if an injected conversion is ongoing */
+ if (HAL_IS_BIT_SET(hadc->State, HAL_ADC_STATE_INJ_BUSY))
+ {
+ /* Reset ADC error code fields related to conversions on group regular */
+ CLEAR_BIT(hadc->ErrorCode, (HAL_ADC_ERROR_OVR | HAL_ADC_ERROR_DMA));
+ }
+ else
+ {
+ /* Reset ADC all error code fields */
+ ADC_CLEAR_ERRORCODE(hadc);
+ }
+
+ /* Process unlocked */
+ /* Unlock before starting ADC conversions: in case of potential */
+ /* interruption, to let the process to ADC IRQ Handler. */
+ __HAL_UNLOCK(hadc);
+
+ /* Clear regular group conversion flag and overrun flag */
+ /* (To ensure of no unknown state from potential previous ADC operations) */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_EOC);
+
+ /* Enable end of conversion interrupt for regular group */
+ __HAL_ADC_ENABLE_IT(hadc, ADC_IT_EOC);
+
+ /* Enable conversion of regular group. */
+ /* If software start has been selected, conversion starts immediately. */
+ /* If external trigger has been selected, conversion will start at next */
+ /* trigger event. */
+ /* Case of multimode enabled: */
+ /* - if ADC is slave, ADC is enabled only (conversion is not started). */
+ /* - if ADC is master, ADC is enabled and conversion is started. */
+ if (ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
+ ADC_NONMULTIMODE_OR_MULTIMODEMASTER(hadc) )
+ {
+ /* Start ADC conversion on regular group with SW start */
+ SET_BIT(hadc->Instance->CR2, (ADC_CR2_SWSTART | ADC_CR2_EXTTRIG));
+ }
+ else
+ {
+ /* Start ADC conversion on regular group with external trigger */
+ SET_BIT(hadc->Instance->CR2, ADC_CR2_EXTTRIG);
+ }
+ }
+ else
+ {
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+ }
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Stop ADC conversion of regular group (and injected group in
+ * case of auto_injection mode), disable interrution of
+ * end-of-conversion, disable ADC peripheral.
+ * @param hadc: ADC handle
+ * @retval None
+ */
+HAL_StatusTypeDef HAL_ADC_Stop_IT(ADC_HandleTypeDef* hadc)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Stop potential conversion on going, on regular and injected groups */
+ /* Disable ADC peripheral */
+ tmp_hal_status = ADC_ConversionStop_Disable(hadc);
+
+ /* Check if ADC is effectively disabled */
+ if (tmp_hal_status == HAL_OK)
+ {
+ /* Disable ADC end of conversion interrupt for regular group */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC);
+
+ /* Set ADC state */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_REG_BUSY | HAL_ADC_STATE_INJ_BUSY,
+ HAL_ADC_STATE_READY);
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Enables ADC, starts conversion of regular group and transfers result
+ * through DMA.
+ * Interruptions enabled in this function:
+ * - DMA transfer complete
+ * - DMA half transfer
+ * Each of these interruptions has its dedicated callback function.
+ * @note For devices with several ADCs: This function is for single-ADC mode
+ * only. For multimode, use the dedicated MultimodeStart function.
+ * @note On STM32F1 devices, only ADC1 and ADC3 (ADC availability depending
+ * on devices) have DMA capability.
+ * ADC2 converted data can be transferred in dual ADC mode using DMA
+ * of ADC1 (ADC master in multimode).
+ * In case of using ADC1 with DMA on a device featuring 2 ADC
+ * instances: ADC1 conversion register DR contains ADC1 conversion
+ * result (ADC1 register DR bits 0 to 11) and, additionally, ADC2 last
+ * conversion result (ADC1 register DR bits 16 to 27). Therefore, to
+ * have DMA transferring the conversion results of ADC1 only, DMA must
+ * be configured to transfer size: half word.
+ * @param hadc: ADC handle
+ * @param pData: The destination Buffer address.
+ * @param Length: The length of data to be transferred from ADC peripheral to memory.
+ * @retval None
+ */
+HAL_StatusTypeDef HAL_ADC_Start_DMA(ADC_HandleTypeDef* hadc, uint32_t* pData, uint32_t Length)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_DMA_CAPABILITY_INSTANCE(hadc->Instance));
+
+ /* Verification if multimode is disabled (for devices with several ADC) */
+ /* If multimode is enabled, dedicated function multimode conversion */
+ /* start DMA must be used. */
+ if(ADC_MULTIMODE_IS_ENABLE(hadc) == RESET)
+ {
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Enable the ADC peripheral */
+ tmp_hal_status = ADC_Enable(hadc);
+
+ /* Start conversion if ADC is effectively enabled */
+ if (tmp_hal_status == HAL_OK)
+ {
+ /* Set ADC state */
+ /* - Clear state bitfield related to regular group conversion results */
+ /* - Set state bitfield related to regular operation */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_READY | HAL_ADC_STATE_REG_EOC | HAL_ADC_STATE_REG_OVR | HAL_ADC_STATE_REG_EOSMP,
+ HAL_ADC_STATE_REG_BUSY);
+
+ /* Set group injected state (from auto-injection) and multimode state */
+ /* for all cases of multimode: independent mode, multimode ADC master */
+ /* or multimode ADC slave (for devices with several ADCs): */
+ if (ADC_NONMULTIMODE_OR_MULTIMODEMASTER(hadc))
+ {
+ /* Set ADC state (ADC independent or master) */
+ CLEAR_BIT(hadc->State, HAL_ADC_STATE_MULTIMODE_SLAVE);
+
+ /* If conversions on group regular are also triggering group injected, */
+ /* update ADC state. */
+ if (READ_BIT(hadc->Instance->CR1, ADC_CR1_JAUTO) != RESET)
+ {
+ ADC_STATE_CLR_SET(hadc->State, HAL_ADC_STATE_INJ_EOC, HAL_ADC_STATE_INJ_BUSY);
+ }
+ }
+ else
+ {
+ /* Set ADC state (ADC slave) */
+ SET_BIT(hadc->State, HAL_ADC_STATE_MULTIMODE_SLAVE);
+
+ /* If conversions on group regular are also triggering group injected, */
+ /* update ADC state. */
+ if (ADC_MULTIMODE_AUTO_INJECTED(hadc))
+ {
+ ADC_STATE_CLR_SET(hadc->State, HAL_ADC_STATE_INJ_EOC, HAL_ADC_STATE_INJ_BUSY);
+ }
+ }
+
+ /* State machine update: Check if an injected conversion is ongoing */
+ if (HAL_IS_BIT_SET(hadc->State, HAL_ADC_STATE_INJ_BUSY))
+ {
+ /* Reset ADC error code fields related to conversions on group regular */
+ CLEAR_BIT(hadc->ErrorCode, (HAL_ADC_ERROR_OVR | HAL_ADC_ERROR_DMA));
+ }
+ else
+ {
+ /* Reset ADC all error code fields */
+ ADC_CLEAR_ERRORCODE(hadc);
+ }
+
+ /* Process unlocked */
+ /* Unlock before starting ADC conversions: in case of potential */
+ /* interruption, to let the process to ADC IRQ Handler. */
+ __HAL_UNLOCK(hadc);
+
+ /* Set the DMA transfer complete callback */
+ hadc->DMA_Handle->XferCpltCallback = ADC_DMAConvCplt;
+
+ /* Set the DMA half transfer complete callback */
+ hadc->DMA_Handle->XferHalfCpltCallback = ADC_DMAHalfConvCplt;
+
+ /* Set the DMA error callback */
+ hadc->DMA_Handle->XferErrorCallback = ADC_DMAError;
+
+
+ /* Manage ADC and DMA start: ADC overrun interruption, DMA start, ADC */
+ /* start (in case of SW start): */
+
+ /* Clear regular group conversion flag and overrun flag */
+ /* (To ensure of no unknown state from potential previous ADC */
+ /* operations) */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_EOC);
+
+ /* Enable ADC DMA mode */
+ SET_BIT(hadc->Instance->CR2, ADC_CR2_DMA);
+
+ /* Start the DMA channel */
+ HAL_DMA_Start_IT(hadc->DMA_Handle, (uint32_t)&hadc->Instance->DR, (uint32_t)pData, Length);
+
+ /* Enable conversion of regular group. */
+ /* If software start has been selected, conversion starts immediately. */
+ /* If external trigger has been selected, conversion will start at next */
+ /* trigger event. */
+ if (ADC_IS_SOFTWARE_START_REGULAR(hadc))
+ {
+ /* Start ADC conversion on regular group with SW start */
+ SET_BIT(hadc->Instance->CR2, (ADC_CR2_SWSTART | ADC_CR2_EXTTRIG));
+ }
+ else
+ {
+ /* Start ADC conversion on regular group with external trigger */
+ SET_BIT(hadc->Instance->CR2, ADC_CR2_EXTTRIG);
+ }
+ }
+ else
+ {
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+ }
+ }
+ else
+ {
+ tmp_hal_status = HAL_ERROR;
+ }
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Stop ADC conversion of regular group (and injected group in
+ * case of auto_injection mode), disable ADC DMA transfer, disable
+ * ADC peripheral.
+ * @note: ADC peripheral disable is forcing stop of potential
+ * conversion on injected group. If injected group is under use, it
+ * should be preliminarily stopped using HAL_ADCEx_InjectedStop function.
+ * @note For devices with several ADCs: This function is for single-ADC mode
+ * only. For multimode, use the dedicated MultimodeStop function.
+ * @note On STM32F1 devices, only ADC1 and ADC3 (ADC availability depending
+ * on devices) have DMA capability.
+ * @param hadc: ADC handle
+ * @retval HAL status.
+ */
+HAL_StatusTypeDef HAL_ADC_Stop_DMA(ADC_HandleTypeDef* hadc)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_DMA_CAPABILITY_INSTANCE(hadc->Instance));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Stop potential conversion on going, on regular and injected groups */
+ /* Disable ADC peripheral */
+ tmp_hal_status = ADC_ConversionStop_Disable(hadc);
+
+ /* Check if ADC is effectively disabled */
+ if (tmp_hal_status == HAL_OK)
+ {
+ /* Disable ADC DMA mode */
+ CLEAR_BIT(hadc->Instance->CR2, ADC_CR2_DMA);
+
+ /* Disable the DMA channel (in case of DMA in circular mode or stop while */
+ /* DMA transfer is on going) */
+ tmp_hal_status = HAL_DMA_Abort(hadc->DMA_Handle);
+
+ /* Check if DMA channel effectively disabled */
+ if (tmp_hal_status == HAL_OK)
+ {
+ /* Set ADC state */
+ ADC_STATE_CLR_SET(hadc->State,
+ HAL_ADC_STATE_REG_BUSY | HAL_ADC_STATE_INJ_BUSY,
+ HAL_ADC_STATE_READY);
+ }
+ else
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_DMA);
+ }
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Get ADC regular group conversion result.
+ * @note Reading register DR automatically clears ADC flag EOC
+ * (ADC group regular end of unitary conversion).
+ * @note This function does not clear ADC flag EOS
+ * (ADC group regular end of sequence conversion).
+ * Occurrence of flag EOS rising:
+ * - If sequencer is composed of 1 rank, flag EOS is equivalent
+ * to flag EOC.
+ * - If sequencer is composed of several ranks, during the scan
+ * sequence flag EOC only is raised, at the end of the scan sequence
+ * both flags EOC and EOS are raised.
+ * To clear this flag, either use function:
+ * in programming model IT: @ref HAL_ADC_IRQHandler(), in programming
+ * model polling: @ref HAL_ADC_PollForConversion()
+ * or @ref __HAL_ADC_CLEAR_FLAG(&hadc, ADC_FLAG_EOS).
+ * @param hadc: ADC handle
+ * @retval ADC group regular conversion data
+ */
+uint32_t HAL_ADC_GetValue(ADC_HandleTypeDef* hadc)
+{
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+
+ /* Note: EOC flag is not cleared here by software because automatically */
+ /* cleared by hardware when reading register DR. */
+
+ /* Return ADC converted value */
+ return hadc->Instance->DR;
+}
+
+/**
+ * @brief Handles ADC interrupt request
+ * @param hadc: ADC handle
+ * @retval None
+ */
+void HAL_ADC_IRQHandler(ADC_HandleTypeDef* hadc)
+{
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+ assert_param(IS_FUNCTIONAL_STATE(hadc->Init.ContinuousConvMode));
+ assert_param(IS_ADC_REGULAR_NB_CONV(hadc->Init.NbrOfConversion));
+
+
+ /* ========== Check End of Conversion flag for regular group ========== */
+ if(__HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_EOC))
+ {
+ if(__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_EOC) )
+ {
+ /* Update state machine on conversion status if not in error state */
+ if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL))
+ {
+ /* Set ADC state */
+ SET_BIT(hadc->State, HAL_ADC_STATE_REG_EOC);
+ }
+
+ /* Determine whether any further conversion upcoming on group regular */
+ /* by external trigger, continuous mode or scan sequence on going. */
+ /* Note: On STM32F1 devices, in case of sequencer enabled */
+ /* (several ranks selected), end of conversion flag is raised */
+ /* at the end of the sequence. */
+ if(ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
+ (hadc->Init.ContinuousConvMode == DISABLE) )
+ {
+ /* Disable ADC end of conversion interrupt on group regular */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC);
+
+ /* Set ADC state */
+ CLEAR_BIT(hadc->State, HAL_ADC_STATE_REG_BUSY);
+
+ if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_INJ_BUSY))
+ {
+ SET_BIT(hadc->State, HAL_ADC_STATE_READY);
+ }
+ }
+
+ /* Conversion complete callback */
+ HAL_ADC_ConvCpltCallback(hadc);
+
+ /* Clear regular group conversion flag */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_STRT | ADC_FLAG_EOC);
+ }
+ }
+
+ /* ========== Check End of Conversion flag for injected group ========== */
+ if(__HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_JEOC))
+ {
+ if(__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_JEOC))
+ {
+ /* Update state machine on conversion status if not in error state */
+ if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL))
+ {
+ /* Set ADC state */
+ SET_BIT(hadc->State, HAL_ADC_STATE_INJ_EOC);
+ }
+
+ /* Determine whether any further conversion upcoming on group injected */
+ /* by external trigger, scan sequence on going or by automatic injected */
+ /* conversion from group regular (same conditions as group regular */
+ /* interruption disabling above). */
+ /* Note: On STM32F1 devices, in case of sequencer enabled */
+ /* (several ranks selected), end of conversion flag is raised */
+ /* at the end of the sequence. */
+ if(ADC_IS_SOFTWARE_START_INJECTED(hadc) ||
+ (HAL_IS_BIT_CLR(hadc->Instance->CR1, ADC_CR1_JAUTO) &&
+ (ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
+ (hadc->Init.ContinuousConvMode == DISABLE) ) ) )
+ {
+ /* Disable ADC end of conversion interrupt on group injected */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_JEOC);
+
+ /* Set ADC state */
+ CLEAR_BIT(hadc->State, HAL_ADC_STATE_INJ_BUSY);
+
+ if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_REG_BUSY))
+ {
+ SET_BIT(hadc->State, HAL_ADC_STATE_READY);
+ }
+ }
+
+ /* Conversion complete callback */
+ HAL_ADCEx_InjectedConvCpltCallback(hadc);
+
+ /* Clear injected group conversion flag */
+ __HAL_ADC_CLEAR_FLAG(hadc, (ADC_FLAG_JSTRT | ADC_FLAG_JEOC));
+ }
+ }
+
+ /* ========== Check Analog watchdog flags ========== */
+ if(__HAL_ADC_GET_IT_SOURCE(hadc, ADC_IT_AWD))
+ {
+ if(__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_AWD))
+ {
+ /* Set ADC state */
+ SET_BIT(hadc->State, HAL_ADC_STATE_AWD1);
+
+ /* Level out of window callback */
+ HAL_ADC_LevelOutOfWindowCallback(hadc);
+
+ /* Clear the ADC analog watchdog flag */
+ __HAL_ADC_CLEAR_FLAG(hadc, ADC_FLAG_AWD);
+ }
+ }
+
+}
+
+/**
+ * @brief Conversion complete callback in non blocking mode
+ * @param hadc: ADC handle
+ * @retval None
+ */
+__weak void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* hadc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hadc);
+ /* NOTE : This function should not be modified. When the callback is needed,
+ function HAL_ADC_ConvCpltCallback must be implemented in the user file.
+ */
+}
+
+/**
+ * @brief Conversion DMA half-transfer callback in non blocking mode
+ * @param hadc: ADC handle
+ * @retval None
+ */
+__weak void HAL_ADC_ConvHalfCpltCallback(ADC_HandleTypeDef* hadc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hadc);
+ /* NOTE : This function should not be modified. When the callback is needed,
+ function HAL_ADC_ConvHalfCpltCallback must be implemented in the user file.
+ */
+}
+
+/**
+ * @brief Analog watchdog callback in non blocking mode.
+ * @param hadc: ADC handle
+ * @retval None
+ */
+__weak void HAL_ADC_LevelOutOfWindowCallback(ADC_HandleTypeDef* hadc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hadc);
+ /* NOTE : This function should not be modified. When the callback is needed,
+ function HAL_ADC_LevelOutOfWindowCallback must be implemented in the user file.
+ */
+}
+
+/**
+ * @brief ADC error callback in non blocking mode
+ * (ADC conversion with interruption or transfer by DMA)
+ * @param hadc: ADC handle
+ * @retval None
+ */
+__weak void HAL_ADC_ErrorCallback(ADC_HandleTypeDef *hadc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hadc);
+ /* NOTE : This function should not be modified. When the callback is needed,
+ function HAL_ADC_ErrorCallback must be implemented in the user file.
+ */
+}
+
+
+/**
+ * @}
+ */
+
+/** @defgroup ADC_Exported_Functions_Group3 Peripheral Control functions
+ * @brief Peripheral Control functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral Control functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+ (+) Configure channels on regular group
+ (+) Configure the analog watchdog
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Configures the the selected channel to be linked to the regular
+ * group.
+ * @note In case of usage of internal measurement channels:
+ * Vbat/VrefInt/TempSensor.
+ * These internal paths can be be disabled using function
+ * HAL_ADC_DeInit().
+ * @note Possibility to update parameters on the fly:
+ * This function initializes channel into regular group, following
+ * calls to this function can be used to reconfigure some parameters
+ * of structure "ADC_ChannelConfTypeDef" on the fly, without reseting
+ * the ADC.
+ * The setting of these parameters is conditioned to ADC state.
+ * For parameters constraints, see comments of structure
+ * "ADC_ChannelConfTypeDef".
+ * @param hadc: ADC handle
+ * @param sConfig: Structure of ADC channel for regular group.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef* hadc, ADC_ChannelConfTypeDef* sConfig)
+{
+ HAL_StatusTypeDef tmp_hal_status = HAL_OK;
+ __IO uint32_t wait_loop_index = 0U;
+
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+ assert_param(IS_ADC_CHANNEL(sConfig->Channel));
+ assert_param(IS_ADC_REGULAR_RANK(sConfig->Rank));
+ assert_param(IS_ADC_SAMPLE_TIME(sConfig->SamplingTime));
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+
+ /* Regular sequence configuration */
+ /* For Rank 1 to 6 */
+ if (sConfig->Rank < 7U)
+ {
+ MODIFY_REG(hadc->Instance->SQR3 ,
+ ADC_SQR3_RK(ADC_SQR3_SQ1, sConfig->Rank) ,
+ ADC_SQR3_RK(sConfig->Channel, sConfig->Rank) );
+ }
+ /* For Rank 7 to 12 */
+ else if (sConfig->Rank < 13U)
+ {
+ MODIFY_REG(hadc->Instance->SQR2 ,
+ ADC_SQR2_RK(ADC_SQR2_SQ7, sConfig->Rank) ,
+ ADC_SQR2_RK(sConfig->Channel, sConfig->Rank) );
+ }
+ /* For Rank 13 to 16 */
+ else
+ {
+ MODIFY_REG(hadc->Instance->SQR1 ,
+ ADC_SQR1_RK(ADC_SQR1_SQ13, sConfig->Rank) ,
+ ADC_SQR1_RK(sConfig->Channel, sConfig->Rank) );
+ }
+
+
+ /* Channel sampling time configuration */
+ /* For channels 10 to 17 */
+ if (sConfig->Channel >= ADC_CHANNEL_10)
+ {
+ MODIFY_REG(hadc->Instance->SMPR1 ,
+ ADC_SMPR1(ADC_SMPR1_SMP10, sConfig->Channel) ,
+ ADC_SMPR1(sConfig->SamplingTime, sConfig->Channel) );
+ }
+ else /* For channels 0 to 9 */
+ {
+ MODIFY_REG(hadc->Instance->SMPR2 ,
+ ADC_SMPR2(ADC_SMPR2_SMP0, sConfig->Channel) ,
+ ADC_SMPR2(sConfig->SamplingTime, sConfig->Channel) );
+ }
+
+ /* If ADC1 Channel_16 or Channel_17 is selected, enable Temperature sensor */
+ /* and VREFINT measurement path. */
+ if ((sConfig->Channel == ADC_CHANNEL_TEMPSENSOR) ||
+ (sConfig->Channel == ADC_CHANNEL_VREFINT) )
+ {
+ /* For STM32F1 devices with several ADC: Only ADC1 can access internal */
+ /* measurement channels (VrefInt/TempSensor). If these channels are */
+ /* intended to be set on other ADC instances, an error is reported. */
+ if (hadc->Instance == ADC1)
+ {
+ if (READ_BIT(hadc->Instance->CR2, ADC_CR2_TSVREFE) == RESET)
+ {
+ SET_BIT(hadc->Instance->CR2, ADC_CR2_TSVREFE);
+
+ if ((sConfig->Channel == ADC_CHANNEL_TEMPSENSOR))
+ {
+ /* Delay for temperature sensor stabilization time */
+ /* Compute number of CPU cycles to wait for */
+ wait_loop_index = (ADC_TEMPSENSOR_DELAY_US * (SystemCoreClock / 1000000U));
+ while(wait_loop_index != 0U)
+ {
+ wait_loop_index--;
+ }
+ }
+ }
+ }
+ else
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_CONFIG);
+
+ tmp_hal_status = HAL_ERROR;
+ }
+ }
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return tmp_hal_status;
+}
+
+/**
+ * @brief Configures the analog watchdog.
+ * @note Analog watchdog thresholds can be modified while ADC conversion
+ * is on going.
+ * In this case, some constraints must be taken into account:
+ * the programmed threshold values are effective from the next
+ * ADC EOC (end of unitary conversion).
+ * Considering that registers write delay may happen due to
+ * bus activity, this might cause an uncertainty on the
+ * effective timing of the new programmed threshold values.
+ * @param hadc: ADC handle
+ * @param AnalogWDGConfig: Structure of ADC analog watchdog configuration
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef* hadc, ADC_AnalogWDGConfTypeDef* AnalogWDGConfig)
+{
+ /* Check the parameters */
+ assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
+ assert_param(IS_ADC_ANALOG_WATCHDOG_MODE(AnalogWDGConfig->WatchdogMode));
+ assert_param(IS_FUNCTIONAL_STATE(AnalogWDGConfig->ITMode));
+ assert_param(IS_ADC_RANGE(AnalogWDGConfig->HighThreshold));
+ assert_param(IS_ADC_RANGE(AnalogWDGConfig->LowThreshold));
+
+ if((AnalogWDGConfig->WatchdogMode == ADC_ANALOGWATCHDOG_SINGLE_REG) ||
+ (AnalogWDGConfig->WatchdogMode == ADC_ANALOGWATCHDOG_SINGLE_INJEC) ||
+ (AnalogWDGConfig->WatchdogMode == ADC_ANALOGWATCHDOG_SINGLE_REGINJEC) )
+ {
+ assert_param(IS_ADC_CHANNEL(AnalogWDGConfig->Channel));
+ }
+
+ /* Process locked */
+ __HAL_LOCK(hadc);
+
+ /* Analog watchdog configuration */
+
+ /* Configure ADC Analog watchdog interrupt */
+ if(AnalogWDGConfig->ITMode == ENABLE)
+ {
+ /* Enable the ADC Analog watchdog interrupt */
+ __HAL_ADC_ENABLE_IT(hadc, ADC_IT_AWD);
+ }
+ else
+ {
+ /* Disable the ADC Analog watchdog interrupt */
+ __HAL_ADC_DISABLE_IT(hadc, ADC_IT_AWD);
+ }
+
+ /* Configuration of analog watchdog: */
+ /* - Set the analog watchdog enable mode: regular and/or injected groups, */
+ /* one or all channels. */
+ /* - Set the Analog watchdog channel (is not used if watchdog */
+ /* mode "all channels": ADC_CFGR_AWD1SGL=0). */
+ MODIFY_REG(hadc->Instance->CR1 ,
+ ADC_CR1_AWDSGL |
+ ADC_CR1_JAWDEN |
+ ADC_CR1_AWDEN |
+ ADC_CR1_AWDCH ,
+ AnalogWDGConfig->WatchdogMode |
+ AnalogWDGConfig->Channel );
+
+ /* Set the high threshold */
+ WRITE_REG(hadc->Instance->HTR, AnalogWDGConfig->HighThreshold);
+
+ /* Set the low threshold */
+ WRITE_REG(hadc->Instance->LTR, AnalogWDGConfig->LowThreshold);
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ /* Return function status */
+ return HAL_OK;
+}
+
+
+/**
+ * @}
+ */
+
+
+/** @defgroup ADC_Exported_Functions_Group4 Peripheral State functions
+ * @brief Peripheral State functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral State and Errors functions #####
+ ===============================================================================
+ [..]
+ This subsection provides functions to get in run-time the status of the
+ peripheral.
+ (+) Check the ADC state
+ (+) Check the ADC error code
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief return the ADC state
+ * @param hadc: ADC handle
+ * @retval HAL state
+ */
+uint32_t HAL_ADC_GetState(ADC_HandleTypeDef* hadc)
+{
+ /* Return ADC state */
+ return hadc->State;
+}
+
+/**
+ * @brief Return the ADC error code
+ * @param hadc: ADC handle
+ * @retval ADC Error Code
+ */
+uint32_t HAL_ADC_GetError(ADC_HandleTypeDef *hadc)
+{
+ return hadc->ErrorCode;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup ADC_Private_Functions ADC Private Functions
+ * @{
+ */
+
+/**
+ * @brief Enable the selected ADC.
+ * @note Prerequisite condition to use this function: ADC must be disabled
+ * and voltage regulator must be enabled (done into HAL_ADC_Init()).
+ * @param hadc: ADC handle
+ * @retval HAL status.
+ */
+HAL_StatusTypeDef ADC_Enable(ADC_HandleTypeDef* hadc)
+{
+ uint32_t tickstart = 0U;
+ __IO uint32_t wait_loop_index = 0U;
+
+ /* ADC enable and wait for ADC ready (in case of ADC is disabled or */
+ /* enabling phase not yet completed: flag ADC ready not yet set). */
+ /* Timeout implemented to not be stuck if ADC cannot be enabled (possible */
+ /* causes: ADC clock not running, ...). */
+ if (ADC_IS_ENABLE(hadc) == RESET)
+ {
+ /* Enable the Peripheral */
+ __HAL_ADC_ENABLE(hadc);
+
+ /* Delay for ADC stabilization time */
+ /* Compute number of CPU cycles to wait for */
+ wait_loop_index = (ADC_STAB_DELAY_US * (SystemCoreClock / 1000000U));
+ while(wait_loop_index != 0U)
+ {
+ wait_loop_index--;
+ }
+
+ /* Get tick count */
+ tickstart = HAL_GetTick();
+
+ /* Wait for ADC effectively enabled */
+ while(ADC_IS_ENABLE(hadc) == RESET)
+ {
+ if((HAL_GetTick() - tickstart) > ADC_ENABLE_TIMEOUT)
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
+
+ /* Set ADC error code to ADC IP internal error */
+ SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
+
+ /* Process unlocked */
+ __HAL_UNLOCK(hadc);
+
+ return HAL_ERROR;
+ }
+ }
+ }
+
+ /* Return HAL status */
+ return HAL_OK;
+}
+
+/**
+ * @brief Stop ADC conversion and disable the selected ADC
+ * @note Prerequisite condition to use this function: ADC conversions must be
+ * stopped to disable the ADC.
+ * @param hadc: ADC handle
+ * @retval HAL status.
+ */
+HAL_StatusTypeDef ADC_ConversionStop_Disable(ADC_HandleTypeDef* hadc)
+{
+ uint32_t tickstart = 0U;
+
+ /* Verification if ADC is not already disabled */
+ if (ADC_IS_ENABLE(hadc) != RESET)
+ {
+ /* Disable the ADC peripheral */
+ __HAL_ADC_DISABLE(hadc);
+
+ /* Get tick count */
+ tickstart = HAL_GetTick();
+
+ /* Wait for ADC effectively disabled */
+ while(ADC_IS_ENABLE(hadc) != RESET)
+ {
+ if((HAL_GetTick() - tickstart) > ADC_DISABLE_TIMEOUT)
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
+
+ /* Set ADC error code to ADC IP internal error */
+ SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
+
+ return HAL_ERROR;
+ }
+ }
+ }
+
+ /* Return HAL status */
+ return HAL_OK;
+}
+
+/**
+ * @brief DMA transfer complete callback.
+ * @param hdma: pointer to DMA handle.
+ * @retval None
+ */
+void ADC_DMAConvCplt(DMA_HandleTypeDef *hdma)
+{
+ /* Retrieve ADC handle corresponding to current DMA handle */
+ ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
+
+ /* Update state machine on conversion status if not in error state */
+ if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL | HAL_ADC_STATE_ERROR_DMA))
+ {
+ /* Update ADC state machine */
+ SET_BIT(hadc->State, HAL_ADC_STATE_REG_EOC);
+
+ /* Determine whether any further conversion upcoming on group regular */
+ /* by external trigger, continuous mode or scan sequence on going. */
+ /* Note: On STM32F1 devices, in case of sequencer enabled */
+ /* (several ranks selected), end of conversion flag is raised */
+ /* at the end of the sequence. */
+ if(ADC_IS_SOFTWARE_START_REGULAR(hadc) &&
+ (hadc->Init.ContinuousConvMode == DISABLE) )
+ {
+ /* Set ADC state */
+ CLEAR_BIT(hadc->State, HAL_ADC_STATE_REG_BUSY);
+
+ if (HAL_IS_BIT_CLR(hadc->State, HAL_ADC_STATE_INJ_BUSY))
+ {
+ SET_BIT(hadc->State, HAL_ADC_STATE_READY);
+ }
+ }
+
+ /* Conversion complete callback */
+ HAL_ADC_ConvCpltCallback(hadc);
+ }
+ else
+ {
+ /* Call DMA error callback */
+ hadc->DMA_Handle->XferErrorCallback(hdma);
+ }
+}
+
+/**
+ * @brief DMA half transfer complete callback.
+ * @param hdma: pointer to DMA handle.
+ * @retval None
+ */
+void ADC_DMAHalfConvCplt(DMA_HandleTypeDef *hdma)
+{
+ /* Retrieve ADC handle corresponding to current DMA handle */
+ ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
+
+ /* Half conversion callback */
+ HAL_ADC_ConvHalfCpltCallback(hadc);
+}
+
+/**
+ * @brief DMA error callback
+ * @param hdma: pointer to DMA handle.
+ * @retval None
+ */
+void ADC_DMAError(DMA_HandleTypeDef *hdma)
+{
+ /* Retrieve ADC handle corresponding to current DMA handle */
+ ADC_HandleTypeDef* hadc = ( ADC_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent;
+
+ /* Set ADC state */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_DMA);
+
+ /* Set ADC error code to DMA error */
+ SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_DMA);
+
+ /* Error callback */
+ HAL_ADC_ErrorCallback(hadc);
+}
+
+/**
+ * @}
+ */
+
+#endif /* HAL_ADC_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|