diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/Config_Reference.md | 24 |
1 files changed, 24 insertions, 0 deletions
diff --git a/docs/Config_Reference.md b/docs/Config_Reference.md index dd444956..549b96ec 100644 --- a/docs/Config_Reference.md +++ b/docs/Config_Reference.md @@ -1650,6 +1650,8 @@ accelerometers (one may define any number of sections with an # Default is 104 (0x68). If AD0 is high, it would be 0x69 instead. #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: 400000 # See the "common I2C settings" section for a description of the # above parameters. The default "i2c_speed" is 400000. @@ -2370,6 +2372,8 @@ sensor_type: BME280 # (0x77). #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # See the "common I2C settings" section for a description of the # above parameters. @@ -2415,6 +2419,8 @@ sensor_type: # Default is 64 (0x40). #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # See the "common I2C settings" section for a description of the # above parameters. @@ -2448,6 +2454,8 @@ sensor_type: LM75 # (usually with jumpers or hard wired). #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # See the "common I2C settings" section for a description of the # above parameters. @@ -2855,6 +2863,8 @@ PCA9533 LED support. The PCA9533 is used on the mightyboard. # the PCA9533/1, 99 for the PCA9533/2. The default is 98. #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # See the "common I2C settings" section for a description of the # above parameters. @@ -2876,6 +2886,8 @@ PCA9632 LED support. The PCA9632 is used on the FlashForge Dreamer. # 96, 97, 98, or 99. The default is 98. #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # See the "common I2C settings" section for a description of the # above parameters. @@ -3622,6 +3634,8 @@ i2c_address: # parameter must be provided. #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # See the "common I2C settings" section for a description of the # above parameters. @@ -3658,6 +3672,8 @@ prefix). # is 96. #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # See the "common I2C settings" section for a description of the # above parameters. @@ -3928,6 +3944,8 @@ lcd_type: # Set to either "ssd1306" or "sh1106" for the given display type. #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # Optional parameters available for displays connected via an i2c # bus. See the "common I2C settings" section for a description of @@ -4308,10 +4326,14 @@ i2c_address: # 113. This parameter must be provided. #i2c_mcu: #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: #i2c_speed: # See the "common I2C settings" section for a description of the # above parameters. #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: # If the I2C implementation of your micro-controller supports # multiple I2C busses, you may specify the bus name here. The # default is to use the default micro-controller i2c bus. @@ -4561,6 +4583,8 @@ via the `i2c_speed` parameter. All other Klipper micro-controllers use a # The name of the micro-controller that the chip is connected to. # The default is "mcu". #i2c_bus: +#i2c_software_scl_pin: +#i2c_software_sda_pin: # If the micro-controller supports multiple I2C busses then one may # specify the micro-controller bus name here. The default depends on # the type of micro-controller. |