1 files changed, 147 insertions, 0 deletions
diff --git a/config/printer-sovol-sv06-plus-2023.cfg b/config/printer-sovol-sv06-plus-2023.cfg
new file mode 100644
index 00000000..cb6fbd87
--- /dev/null
+++ b/config/printer-sovol-sv06-plus-2023.cfg
@@ -0,0 +1,147 @@
+# This file contains pin mappings for the stock Sovol SV06 Plus
+# To use this config, during "make menuconfig" select the
+# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.
+# Also, since it is using the GD32F103, please select Disable SWD at startup
+#
+# Flash this firmware by copying "out/klipper.bin" to a SD card and
+# turning on the printer with the card inserted. The firmware
+# filename must end in ".bin" and must not match the last filename
+# that was flashed.
+#
+# Note: The stock LCD display does not currently work with Klipper
+#
+# See docs/Config_Reference.md for a description of parameters.
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 500
+max_accel: 2000
+max_z_velocity: 10
+max_z_accel: 100
+
+[stepper_x]
+step_pin: PC2
+dir_pin: !PB9
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_x:virtual_endstop
+position_endstop: 0
+position_max: 305
+homing_speed: 40
+homing_retract_dist: 0
+
+[tmc2209 stepper_x]
+uart_pin: PC1
+run_current: 0.860
+sense_resistor: 0.150
+uart_address: 3
+driver_SGTHRS: 81
+diag_pin: PA5
+
+[stepper_y]
+step_pin: PB8
+dir_pin: PB7
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: tmc2209_stepper_y:virtual_endstop
+position_endstop: 0
+position_max: 305
+homing_speed: 40
+homing_retract_dist: 0
+
+[tmc2209 stepper_y]
+uart_pin: PC0
+run_current: 0.900
+sense_resistor: 0.150
+uart_address: 3
+driver_SGTHRS: 82
+diag_pin: PA6
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 4
+endstop_pin: probe:z_virtual_endstop
+position_min: -4
+position_max: 350
+homing_speed: 4
+
+[tmc2209 stepper_z]
+uart_pin: PA15
+run_current: 1.000
+interpolate: False
+sense_resistor: 0.150
+uart_address: 3
+diag_pin: PA7
+
+[extruder]
+max_extrude_only_distance: 100.0
+step_pin: PB4
+dir_pin: !PB3
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 4.56
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+control: pid
+pid_kd: 41.96
+pid_kp: 15.66
+pid_ki: 1.49
+min_temp: 0
+max_temp: 300
+
+[tmc2209 extruder]
+uart_pin: PC14
+run_current: 0.550
+stealthchop_threshold: 0
+interpolate: False
+sense_resistor: 0.150
+uart_address: 3
+
+[heater_bed]
+heater_pin: PA2
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_kp: 186.38
+pid_ki: 36.12
+pid_kd: 637.30
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PA0
+
+[probe]
+pin: PB1
+x_offset: 28
+y_offset: -20
+z_offset: 0
+
+[safe_z_home]
+home_xy_position: 123,170
+z_hop: 10
+z_hop_speed: 5
+
+[bed_mesh]
+speed: 120
+mesh_min: 28, 20
+mesh_max: 270, 270
+probe_count: 5
+algorithm: bicubic
+fade_end: 10
+fade_target: 0
+
+[filament_switch_sensor filament_runout_sensor]
+switch_pin: PA4
+pause_on_runout: True