aboutsummaryrefslogtreecommitdiffstats
path: root/config
diff options
context:
space:
mode:
Diffstat (limited to 'config')
-rw-r--r--config/generic-bigtreetech-manta-m8p-v1.0.cfg2
-rw-r--r--config/generic-bigtreetech-manta-m8p-v1.1.cfg2
-rw-r--r--config/generic-bigtreetech-octopus-max-ez.cfg2
-rw-r--r--config/generic-bigtreetech-octopus-v1.1.cfg2
-rw-r--r--config/kit-voron2-250mm.cfg2
-rw-r--r--config/kit-zav3d-2019.cfg2
-rw-r--r--config/printer-anycubic-kossel-2016.cfg2
-rw-r--r--config/printer-creality-cr10-v3-2020.cfg2
-rw-r--r--config/printer-creality-ender5-s1-2023.cfg2
-rw-r--r--config/printer-lulzbot-mini1-2016.cfg2
-rw-r--r--config/printer-lulzbot-taz6-dual-v3-2017.cfg2
-rw-r--r--config/printer-robo3d-r2-2017.cfg2
-rw-r--r--config/printer-seemecnc-rostock-max-v2-2015.cfg2
-rw-r--r--config/sample-duet3-1lc.cfg2
-rw-r--r--config/sample-mmu2s-diy.cfg6
15 files changed, 17 insertions, 17 deletions
diff --git a/config/generic-bigtreetech-manta-m8p-v1.0.cfg b/config/generic-bigtreetech-manta-m8p-v1.0.cfg
index 2a801cde..4459076f 100644
--- a/config/generic-bigtreetech-manta-m8p-v1.0.cfg
+++ b/config/generic-bigtreetech-manta-m8p-v1.0.cfg
@@ -39,7 +39,7 @@ position_max: 270
# Motor4
# The M8P only has 4 heater outputs which leaves an extra stepper
# This can be used for a second Z stepper, dual_carriage, extruder co-stepper,
-# or other accesory such as an MMU
+# or other accessory such as an MMU
#[stepper_]
#step_pin: PD3
#dir_pin: PD2
diff --git a/config/generic-bigtreetech-manta-m8p-v1.1.cfg b/config/generic-bigtreetech-manta-m8p-v1.1.cfg
index 36ef710c..aadb5c45 100644
--- a/config/generic-bigtreetech-manta-m8p-v1.1.cfg
+++ b/config/generic-bigtreetech-manta-m8p-v1.1.cfg
@@ -40,7 +40,7 @@ position_max: 270
# Motor4
# The M8P only has 4 heater outputs which leaves an extra stepper
# This can be used for a second Z stepper, dual_carriage, extruder co-stepper,
-# or other accesory such as an MMU
+# or other accessory such as an MMU
#[stepper_]
#step_pin: PD3
#dir_pin: PD2
diff --git a/config/generic-bigtreetech-octopus-max-ez.cfg b/config/generic-bigtreetech-octopus-max-ez.cfg
index 60822b04..3ccc2c75 100644
--- a/config/generic-bigtreetech-octopus-max-ez.cfg
+++ b/config/generic-bigtreetech-octopus-max-ez.cfg
@@ -43,7 +43,7 @@ position_max: 200
# Motor-4
# The Octopus only has 4 heater outputs which leaves an extra stepper
# This can be used for a second Z stepper, dual_carriage, extruder co-stepper,
-# or other accesory such as an MMU
+# or other accessory such as an MMU
#[stepper_]
#step_pin: PB8
#dir_pin: PB9
diff --git a/config/generic-bigtreetech-octopus-v1.1.cfg b/config/generic-bigtreetech-octopus-v1.1.cfg
index f3a2b87c..dcd0e97c 100644
--- a/config/generic-bigtreetech-octopus-v1.1.cfg
+++ b/config/generic-bigtreetech-octopus-v1.1.cfg
@@ -52,7 +52,7 @@ position_max: 200
# Driver3
# The Octopus only has 4 heater outputs which leaves an extra stepper
# This can be used for a second Z stepper, dual_carriage, extruder co-stepper,
-# or other accesory such as an MMU
+# or other accessory such as an MMU
#[stepper_]
#step_pin: PG4
#dir_pin: PC1
diff --git a/config/kit-voron2-250mm.cfg b/config/kit-voron2-250mm.cfg
index 343e9c67..e82ee28a 100644
--- a/config/kit-voron2-250mm.cfg
+++ b/config/kit-voron2-250mm.cfg
@@ -19,7 +19,7 @@
# FSR switch (z endstop) location [homing_override] section
# FSR switch (z endstop) offset for Z0 [stepper_z] section
# Probe points [quad_gantry_level] section
-# Min & Max gantry corner postions [quad_gantry_level] section
+# Min & Max gantry corner positions [quad_gantry_level] section
# PID tune [extruder] and [heater_bed] sections
# Fine tune E steps [extruder] section
diff --git a/config/kit-zav3d-2019.cfg b/config/kit-zav3d-2019.cfg
index e3b57b8e..e2385c94 100644
--- a/config/kit-zav3d-2019.cfg
+++ b/config/kit-zav3d-2019.cfg
@@ -20,7 +20,7 @@
# FSR switch (z endstop) location [homing_override] section
# FSR switch (z endstop) offset for Z0 [stepper_z] section
# Probe points [quad_gantry_level] section
-# Min & Max gantry corner postions [quad_gantry_level] section
+# Min & Max gantry corner positions [quad_gantry_level] section
# PID tune [extruder] and [heater_bed] sections
# Fine tune E steps [extruder] section
diff --git a/config/printer-anycubic-kossel-2016.cfg b/config/printer-anycubic-kossel-2016.cfg
index 7df93b41..1f7819f2 100644
--- a/config/printer-anycubic-kossel-2016.cfg
+++ b/config/printer-anycubic-kossel-2016.cfg
@@ -17,7 +17,7 @@ endstop_pin: ^PE4
homing_speed: 60
# The next parameter needs to be adjusted for
# your printer. You may want to start with 280
-# and meassure the distance from nozzle to bed.
+# and measure the distance from nozzle to bed.
# This value then needs to be added.
position_endstop: 273.0
arm_length: 229.4
diff --git a/config/printer-creality-cr10-v3-2020.cfg b/config/printer-creality-cr10-v3-2020.cfg
index 9bf84df5..af9e923c 100644
--- a/config/printer-creality-cr10-v3-2020.cfg
+++ b/config/printer-creality-cr10-v3-2020.cfg
@@ -43,7 +43,7 @@ position_max: 400
#Uncomment if you have a BL-Touch:
#position_min: -4
#endstop_pin: probe:z_virtual_endstop
-#and comment the follwing lines:
+#and comment the following lines:
position_endstop: 0.0
endstop_pin: ^PD3 #ar18
diff --git a/config/printer-creality-ender5-s1-2023.cfg b/config/printer-creality-ender5-s1-2023.cfg
index 68a89fa5..17bb2a46 100644
--- a/config/printer-creality-ender5-s1-2023.cfg
+++ b/config/printer-creality-ender5-s1-2023.cfg
@@ -81,7 +81,7 @@ pin: PA0
kick_start_time: 0.5
# Hotend fan
-# set fan runnig when extruder temperature is over 60
+# set fan running when extruder temperature is over 60
[heater_fan heatbreak_fan]
pin: PC0
heater:extruder
diff --git a/config/printer-lulzbot-mini1-2016.cfg b/config/printer-lulzbot-mini1-2016.cfg
index 52b8061e..cff0eee4 100644
--- a/config/printer-lulzbot-mini1-2016.cfg
+++ b/config/printer-lulzbot-mini1-2016.cfg
@@ -195,7 +195,7 @@ samples_tolerance: 0.200
samples_tolerance_retries: 2
[bed_tilt]
-# Enable bed tilt measurments using the probe we defined above
+# Enable bed tilt measurements using the probe we defined above
# Probe points using X0 Y0 offsets @ 0.01mm/step
points: -2, -6
156, -6
diff --git a/config/printer-lulzbot-taz6-dual-v3-2017.cfg b/config/printer-lulzbot-taz6-dual-v3-2017.cfg
index f94b0684..f4b23fdb 100644
--- a/config/printer-lulzbot-taz6-dual-v3-2017.cfg
+++ b/config/printer-lulzbot-taz6-dual-v3-2017.cfg
@@ -183,7 +183,7 @@ samples: 2
samples_tolerance: 0.100
[bed_tilt]
-#Enable bed tilt measurments using the probe we defined above
+#Enable bed tilt measurements using the probe we defined above
#Probe points using X0 Y0 offsets @ 0.01mm/step
points: -3, -6
282, -6
diff --git a/config/printer-robo3d-r2-2017.cfg b/config/printer-robo3d-r2-2017.cfg
index a87f4bef..89fe127b 100644
--- a/config/printer-robo3d-r2-2017.cfg
+++ b/config/printer-robo3d-r2-2017.cfg
@@ -37,7 +37,7 @@ microsteps: 16
rotation_distance: 4
# Required if not using probe for the virtual endstop
# endstop_pin: ^PD3
-# position_endstop: 250 # Will need ajustment
+# position_endstop: 250 # Will need adjustment
endstop_pin: probe:z_virtual_endstop
homing_speed: 10.0
position_max: 250
diff --git a/config/printer-seemecnc-rostock-max-v2-2015.cfg b/config/printer-seemecnc-rostock-max-v2-2015.cfg
index 70ebd876..09ea7bdb 100644
--- a/config/printer-seemecnc-rostock-max-v2-2015.cfg
+++ b/config/printer-seemecnc-rostock-max-v2-2015.cfg
@@ -1,4 +1,4 @@
-# This file constains the pin mappings for the SeeMeCNC Rostock Max
+# This file contains the pin mappings for the SeeMeCNC Rostock Max
# (version 2) delta printer from 2015. To use this config, the
# firmware should be compiled for the AVR atmega2560.
diff --git a/config/sample-duet3-1lc.cfg b/config/sample-duet3-1lc.cfg
index ef7e4042..1e0eaf10 100644
--- a/config/sample-duet3-1lc.cfg
+++ b/config/sample-duet3-1lc.cfg
@@ -6,7 +6,7 @@
# Communication interface of "CAN bus (on PA25/PA24)"
# To flash the board use a debugger, or use a raspberry pi and follow
-# the instructions at docs/Bootloaders.md fot the SAMC21. You may
+# the instructions at docs/Bootloaders.md for the SAMC21. You may
# supply power to the 1LC by connecting the 3.3v rail on the Pi to the
# 5v input of the SWD header on the 1LC.
diff --git a/config/sample-mmu2s-diy.cfg b/config/sample-mmu2s-diy.cfg
index d1d7793e..41fe669f 100644
--- a/config/sample-mmu2s-diy.cfg
+++ b/config/sample-mmu2s-diy.cfg
@@ -96,7 +96,7 @@ switch_pin: !P1.28 # P1.28 for X-max
# variable_pause_z : z lift when MMU2S need intervention and the printer is paused
# variable_min_temp_extruder : minimal required heater temperature to load/unload filament from the extruder gear to the nozzle
# variable_extruder_eject_temp : heater temperature used to eject filament during home if the filament is already loaded
-# variable_enable_5in1 : pass from MMU2S standart (0) to MMU2S-5in1 mode with splitter
+# variable_enable_5in1 : pass from MMU2S standard (0) to MMU2S-5in1 mode with splitter
#
################################
[gcode_macro VAR_MMU2S]
@@ -394,7 +394,7 @@ gcode:
{% endif %}
{% endif %}
-# Retry unload, try correct misalignement of bondtech gear
+# Retry unload, try correct misalignment of bondtech gear
[gcode_macro RETRY_UNLOAD_FILAMENT_IN_EXTRUDER]
gcode:
{% if printer["filament_switch_sensor ir_sensor"].filament_detected == True %}
@@ -444,7 +444,7 @@ gcode:
{% endif %}
{% endif %}
-# Ramming process for standart PLA, code extracted from slic3r gcode
+# Ramming process for standard PLA, code extracted from slic3r gcode
[gcode_macro RAMMING_SLICER]
gcode:
G91
generated by cgit v1.2.3-70-g09d2 (git 2.50.1) at 2025-09-02 10:34:16 +0000