diff options
Diffstat (limited to 'config/printer-sunlu-s8-2020.cfg')
| -rw-r--r-- | config/printer-sunlu-s8-2020.cfg | 59 |
1 files changed, 29 insertions, 30 deletions
diff --git a/config/printer-sunlu-s8-2020.cfg b/config/printer-sunlu-s8-2020.cfg index b933ced8..ccf07d21 100644 --- a/config/printer-sunlu-s8-2020.cfg +++ b/config/printer-sunlu-s8-2020.cfg @@ -1,53 +1,53 @@ # This file contains pin mappings for the SUNLU S8 v1.01 (circa 2020), which # is a modified RAMPS v1.3 board. To use this config, the firmware should be # compiled for the AVR atmega2560. The following pins are available for -# expansion (e.g. ABL): ^ar19 (Z+ endstop), ar4, ar5, ar6, ar11 +# expansion (e.g. ABL): ^PD2 (Z+ endstop), PG5, PE3, PH3, PB5 # See docs/Config_Reference.md for a description of parameters. [stepper_x] -step_pin: ar54 -dir_pin: !ar55 -enable_pin: !ar38 +step_pin: PF0 +dir_pin: !PF1 +enable_pin: !PD7 microsteps: 16 rotation_distance: 40 -endstop_pin: ^!ar3 +endstop_pin: ^!PE5 position_endstop: 0 position_max: 310 homing_speed: 50 [stepper_y] -step_pin: ar60 -dir_pin: !ar61 -enable_pin: !ar56 +step_pin: PF6 +dir_pin: !PF7 +enable_pin: !PF2 microsteps: 16 rotation_distance: 40 -endstop_pin: ^!ar14 +endstop_pin: ^!PJ1 position_endstop: 0 position_max: 310 homing_speed: 50 [stepper_z] -step_pin: ar46 -dir_pin: ar48 -enable_pin: !ar62 +step_pin: PL3 +dir_pin: PL1 +enable_pin: !PK0 microsteps: 16 rotation_distance: 8 -endstop_pin: ^!ar18 +endstop_pin: ^!PD3 position_endstop: 0.5 position_max: 400 [extruder] -step_pin: ar26 -dir_pin: !ar28 -enable_pin: !ar24 +step_pin: PA4 +dir_pin: !PA6 +enable_pin: !PA2 microsteps: 16 rotation_distance: 33.280 nozzle_diameter: 0.400 filament_diameter: 1.750 -heater_pin: ar10 +heater_pin: PB4 sensor_type: EPCOS 100K B57560G104F -sensor_pin: analog13 +sensor_pin: PK5 control: pid pid_kp: 25.588 pid_ki: 1.496 @@ -57,12 +57,12 @@ max_temp: 250 [filament_switch_sensor runout] pause_on_runout: True -switch_pin: ^ar2 +switch_pin: ^PE4 [heater_bed] -heater_pin: ar8 +heater_pin: PH5 sensor_type: EPCOS 100K B57560G104F -sensor_pin: analog14 +sensor_pin: PK6 control: pid pid_kp: 74.786 pid_ki: 0.766 @@ -77,14 +77,13 @@ max_temp: 110 check_gain_time: 240 [fan] -pin: ar9 +pin: PH6 [heater_fan fan1] -pin: ar7 +pin: PH4 [mcu] serial: /dev/ttyUSB0 -pin_map: arduino [printer] kinematics: cartesian @@ -95,11 +94,11 @@ max_z_accel: 100 [display] lcd_type: st7920 -cs_pin: ar16 -sclk_pin: ar23 -sid_pin: ar17 -encoder_pins: ^ar33, ^ar31 -click_pin: ^!ar35 +cs_pin: PH1 +sclk_pin: PA1 +sid_pin: PH0 +encoder_pins: ^PC4, ^PC6 +click_pin: ^!PC2 [output_pin beeper] -pin: ar37 +pin: PC0 |