diff options
Diffstat (limited to 'config/printer-lulzbot-taz6-dual-v3-2017.cfg')
| -rw-r--r-- | config/printer-lulzbot-taz6-dual-v3-2017.cfg | 48 |
1 files changed, 12 insertions, 36 deletions
diff --git a/config/printer-lulzbot-taz6-dual-v3-2017.cfg b/config/printer-lulzbot-taz6-dual-v3-2017.cfg index 38248f0d..e7a43653 100644 --- a/config/printer-lulzbot-taz6-dual-v3-2017.cfg +++ b/config/printer-lulzbot-taz6-dual-v3-2017.cfg @@ -214,17 +214,16 @@ gcode: #NOTE: T0 is the default extruder, T1 is optional. #START block for use with dual or single extrusion prints [gcode_macro START_PRINT] -default_parameter_EXTRUDERS_ENABLED_COUNT: 1 -default_parameter_MATERIAL_STANDBY_TEMPERATURE_0: 175 -default_parameter_MATERIAL_STANDBY_TEMPERATURE_1: 175 -default_parameter_MATERIAL_BED_TEMPERATURE_LAYER_0: 65 -default_parameter_MATERIAL_PRINT_TEMPERATURE_LAYER_0_0: 210 -default_parameter_MATERIAL_PRINT_TEMPERATURE_LAYER_0_1: 210 -#configure the params below to tune the stage desired temperatures based on the standby temps -default_parameter_MATERIAL_SOFTEN_TEMP_OFFSET: 35 -default_parameter_MATERIAL_WIPE_TEMP_OFFSET: 35 -default_parameter_MATERIAL_PROBE_TEMP_OFFSET: 35 gcode: + {% set EXTRUDERS_ENABLED_COUNT = 1 %} + {% set MATERIAL_STANDBY_TEMPERATURE_0 = 175 %} + {% set MATERIAL_STANDBY_TEMPERATURE_1 = 175 %} + {% set MATERIAL_BED_TEMPERATURE_LAYER_0 = 65 %} + {% set MATERIAL_PRINT_TEMPERATURE_LAYER_0_0 = 210 %} + {% set MATERIAL_PRINT_TEMPERATURE_LAYER_0_1 = 210 %} + {% set MATERIAL_SOFTEN_TEMP_OFFSET = 35 %} + {% set MATERIAL_WIPE_TEMP_OFFSET = 35 %} + {% set MATERIAL_PROBE_TEMP_OFFSET = 35 %} ;This profile is designed specifically for LulzBot TAZ6 3D Printer with the Yellowfin Dual running Klipper M73 P0 ; clear GLCD progress bar M107 ; disable fans @@ -342,10 +341,10 @@ gcode: #END block for use with dual or single extrusion prints [gcode_macro END_PRINT] -default_parameter_EXTRUDERS_ENABLED_COUNT: 1 -default_parameter_MATERIAL_PART_REMOVAL_TEMPERATURE: 45 -default_parameter_MATERIAL_KEEP_PART_REMOVAL_TEMPERATURE_T: 0 gcode: + {% set EXTRUDERS_ENABLED_COUNT = 1 %} + {% set MATERIAL_PART_REMOVAL_TEMPERATURE = 45 %} + {% set MATERIAL_KEEP_PART_REMOVAL_TEMPERATURE_T = 0 %} M400 M104 S0 T0 ; T0 hotend off {% if EXTRUDERS_ENABLED_COUNT|int == 2 %} @@ -372,26 +371,3 @@ gcode: M84 ; steppers off G90 ; absolute positioning M117 Print Complete ; progress indicator message - -#--------------------------------------------------------------------------------------------------- -# ULTIMAKER CURA START AND END SCRIPTS - Replace default START and STOP scripts with the below GCODE -#--------------------------------------------------------------------------------------------------- -#---> Dual Extrusion Printer Profiles < --- -#; LulzBot Taz6 w/ Dual Extruder Klipper START gcode script (for Cura UE, tested on v4.3) -#; First, set START_PRINT Macro variables from Cura parameters -#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=EXTRUDERS_ENABLED_COUNT VALUE={extruders_enabled_count} -#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_STANDBY_TEMPERATURE_0 VALUE={material_standby_temperature} -#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_STANDBY_TEMPERATURE_1 VALUE={material_standby_temperature, 1} -#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_BED_TEMPERATURE_LAYER_0 VALUE={material_bed_temperature_layer_0} -#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_PRINT_TEMPERATURE_LAYER_0_0 VALUE={material_print_temperature_layer_0} -#SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=MATERIAL_PRINT_TEMPERATURE_LAYER_0_1 VALUE={material_print_temperature_layer_0, 1} -#; Execute START_PRINT GCODE defined in Klipper config file -#START_PRINT - -#; LulzBot Taz6 w/ Dual Extruder v3 Klipper END gcode script (for Cura UE, tested on v4.3) -#; First, set END_PRINT Macro variables from Cura parameters -#SET_GCODE_VARIABLE MACRO=END_PRINT VARIABLE=EXTRUDERS_ENABLED_COUNT VALUE={extruders_enabled_count} -#SET_GCODE_VARIABLE MACRO=END_PRINT VARIABLE=MATERIAL_PART_REMOVAL_TEMPERATURE VALUE=45 -#SET_GCODE_VARIABLE MACRO=END_PRINT VARIABLE=MATERIAL_KEEP_PART_REMOVAL_TEMPERATURE_T VALUE=0 -#; Execute END_PRINT GCODE defined in Klipper config file -#END_PRINT |