1 files changed, 176 insertions, 0 deletions
diff --git a/config/printer-flashforge-creator-pro-2018.cfg b/config/printer-flashforge-creator-pro-2018.cfg
new file mode 100644
index 00000000..176732b5
--- /dev/null
+++ b/config/printer-flashforge-creator-pro-2018.cfg
@@ -0,0 +1,176 @@
+# This file contains common pin mappings for the FlashForge-Creator-Pro
+# To use this config, the firmware should be compiled for
+# the Atmel atmega2560.
+# requires the following command to flash the board:
+#  avrdude -c stk500v2 -p m2560 -P /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_557373136313514061A2-if00 -b 57600 -D -U out/klipper.elf.hex
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PF1
+dir_pin: !PF0
+enable_pin: !PF2
+microsteps: 16
+rotation_distance: 34
+endstop_pin: ^!PL1
+position_endstop: 116
+position_max: 116
+position_min: -116
+homing_speed: 50
+
+[stepper_y]
+step_pin: PF5
+dir_pin: !PF4
+enable_pin: !PF6
+microsteps: 16
+rotation_distance: 34
+endstop_pin: ^!PL3
+position_endstop: 80
+position_max: 80
+position_min: -80
+homing_speed: 50
+
+[stepper_z]
+step_pin: PK1
+dir_pin: !PK0
+enable_pin: !PK2
+microsteps: 16
+rotation_distance: 8
+endstop_pin: !PL6
+position_endstop: -0.25
+position_max: 181
+position_min: -0.25
+
+[extruder]
+step_pin: PA3
+dir_pin: !PA2
+enable_pin: !PA4
+microsteps: 16
+rotation_distance: 33
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PH3
+sensor_type: MAX6675
+sensor_pin: PE3
+spi_software_miso_pin: PE5
+spi_software_sclk_pin: PE2
+spi_software_mosi_pin: PA1 #dummy mosi pin
+control: pid
+pid_kp: 27.341
+pid_ki: 1.293
+pid_kd: 144.566
+min_temp: 0
+max_temp: 260
+
+[extruder1]
+step_pin: PA7
+dir_pin: PA6
+enable_pin: !PG2
+microsteps: 16
+rotation_distance: 33
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PB5
+sensor_type: MAX6675
+sensor_pin: PE4
+spi_software_miso_pin: PE5
+spi_software_sclk_pin: PE2
+spi_software_mosi_pin: PA1 #dummy mosi pin
+control: pid
+pid_kp: 27.341
+pid_ki: 1.293
+pid_kd: 144.566
+min_temp: 0
+max_temp: 260
+
+[gcode_macro T0]
+gcode:
+    SET_GCODE_OFFSET X=-34
+    ACTIVATE_EXTRUDER EXTRUDER=extruder
+
+[gcode_macro T1]
+gcode:
+    SET_GCODE_OFFSET X=0
+    ACTIVATE_EXTRUDER EXTRUDER=extruder1
+
+
+[heater_fan extruder_fan]
+pin: PH4
+
+[heater_fan extruder1_fan]
+pin: PB6
+
+[fan]
+pin: PL5
+
+[heater_bed]
+heater_pin: PL4
+sensor_type: ATC Semitec 104GT-2
+sensor_pin: PK7
+control: pid
+pid_kp: 72.914
+pid_ki: 2.060
+pid_kd: 645.290
+min_temp: 0
+max_temp: 130
+
+[mcu]
+serial: /dev/serial/by-id/usb-MakerBot_Industries_The_Replicator_557373136313514061A2-if00
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 1000
+max_z_velocity: 5
+max_z_accel: 100
+
+[mcp4018 x_axis_pot]
+scl_pin: PJ5
+sda_pin: PF3
+wiper: 118
+scale: 127
+
+[mcp4018 y_axis_pot]
+scl_pin: PJ5
+sda_pin: PF7
+wiper: 118
+scale: 127
+
+[mcp4018 z_axis_pot]
+scl_pin: PJ5
+sda_pin: PK3
+wiper: 40
+scale: 127
+
+[mcp4018 a_axis_pot]
+scl_pin: PJ5
+sda_pin: PA5
+wiper: 118
+scale: 127
+
+[mcp4018 b_axis_pot]
+scl_pin: PJ5
+sda_pin: PJ6
+wiper: 118
+scale: 127
+
+[display]
+lcd_type: hd44780_spi
+spi_software_mosi_pin: PC3
+spi_software_sclk_pin: PC2
+#miso not used, dummy pin.
+spi_software_miso_pin: PJ1
+latch_pin: PC4
+
+click_pin: ^PJ0
+back_pin: ^PJ2
+up_pin: ^PJ4
+down_pin: ^PJ3
+
+[pca9533 led_strip]
+i2c_bus: twi
+i2c_address: 98
+initial_RED: 1
+initial_GREEN: 1
+initial_BLUE: 1