1 files changed, 295 insertions, 0 deletions
diff --git a/config/generic-flyboard.cfg b/config/generic-flyboard.cfg
new file mode 100755
index 00000000..ed07ec10
--- /dev/null
+++ b/config/generic-flyboard.cfg
@@ -0,0 +1,295 @@
+# This file contains common pin mappings for the 9 stepper motor
+# "flymaker flyboard FLYF407ZG" board from creative3dprinter.com. To
+# use this config, the firmware should be compiled for the STM32F407
+# with a "32KiB bootloader".
+
+# The "make flash" command does not work on the FLYBOARD. Instead,
+# after running "make", copy the generated "out/klipper.bin" file to a
+# file named "firmware.bin" on an SD card and then restart the FLYBOARD
+# with that SD card.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: PB9
+dir_pin: PE0
+enable_pin: !PE1
+step_distance: .0025
+endstop_pin: PC3
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_y]
+step_pin: PB8
+dir_pin: PG11
+enable_pin: !PG12
+step_distance: .0025
+endstop_pin: PF2
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_z]
+step_pin: PA8
+dir_pin: PD6
+enable_pin: !PD7
+step_distance: .0125
+endstop_pin: PF0
+position_endstop: 0.5
+position_max: 200
+
+[extruder]
+step_pin: PC7
+dir_pin: PD3
+enable_pin: !PD4
+step_distance: .002
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PF7 # Heat0
+sensor_pin: PA0 # T1 Header
+sensor_type: EPCOS 100K B57560G104F
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 350
+
+#[extruder1]
+#step_pin: PC6
+#dir_pin: PA15
+#enable_pin: !PD0
+#heater_pin: PF6 # Heat1
+#sensor_pin: PC1 # T2
+#...
+
+#[extruder2]
+#step_pin: PD15
+#dir_pin: PG7
+#enable_pin: !PG8
+#heater_pin: PE6 # Heat2
+#sensor_pin: PC0 # T3
+#...
+
+#[extruder3]
+#step_pin: PD14
+#dir_pin: PG4
+#enable_pin: !PG5
+#heater_pin: PE5 # Heat3
+#sensor_pin: PF10 # T4
+#...
+
+#[extruder4]
+#step_pin: PD13
+#dir_pin: PD11
+#enable_pin: !PG2
+#heater_pin: PE4 # Heat4
+#sensor_pin: PF5 # T5
+#...
+
+#[extruder4]
+#step_pin: PD12
+#dir_pin: PD8
+#enable_pin: !PD9
+#heater_pin: PE3 # Heat5
+#sensor_pin: PF4 # T6
+#...
+
+[heater_bed]
+heater_pin: PE2
+sensor_pin: PF3 # T0
+sensor_type: ATC Semitec 104GT-2
+control: watermark
+min_temp: 0
+max_temp: 200
+
+[fan]
+pin: PF8
+
+[heater_fan fan1]
+pin: PF9
+
+#[heater_fan fan2]
+#pin: PA2
+
+#[heater_fan fan3]
+#pin: PA1
+
+#[heater_fan fan4]
+#pin: PE13
+
+#[heater_fan fan5]
+#pin: PB11
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+
+[printer]
+kinematics: corexy
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+
+########################################
+# TMC2208 configuration
+########################################
+
+#[tmc2208 stepper_x]
+#uart_pin: PG13
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 250
+
+#[tmc2208 stepper_y]
+#uart_pin: PG10
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 250
+
+#[tmc2208 stepper_z]
+#uart_pin: PD5
+#microsteps: 16
+#run_current: 0.650
+#hold_current: 0.450
+#stealthchop_threshold: 30
+
+#[tmc2208 extruder]
+#uart_pin: PD1
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2208 extruder1]
+#uart_pin: PA14
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2208 extruder2]
+#uart_pin: PG6
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2208 extruder3]
+#uart_pin: PG3
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2208 extruder4]
+#uart_pin: PD10
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2208 extruder5]
+#uart_pin: PB12
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+
+########################################
+# TMC2130 configuration
+########################################
+
+#[tmc2130 stepper_x]
+#cs_pin: PG13
+##diag1_pin: PC3
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 250
+
+#[tmc2130 stepper_y]
+#cs_pin: PG10
+##diag1_pin: PF2
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 250
+
+#[tmc2130 stepper_z]
+#cs_pin: PBD5
+##diag1_pin: PF0
+#microsteps: 16
+#run_current: 0.650
+#hold_current: 0.450
+#stealthchop_threshold: 30
+
+#[tmc2130 extruder]
+#cs_pin: PD1
+##diag1_pin: PE15
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2130 extruder1]
+#cs_pin: PA14
+##diag1_pin: PE10
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2130 extruder2]
+#cs_pin: PG6
+##diag1_pin: PC15
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2130 extruder3]
+#cs_pin: PG3
+##diag1_pin: PC15
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2130 extruder4]
+#cs_pin: PD10
+##diag1_pin: PC15
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+#[tmc2130 extruder5]
+#cs_pin: PB12
+##diag1_pin: PC15
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+
+########################################
+# EXP1 / EXP2 (display) pins
+########################################
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=PB10, EXP1_3=PE14, EXP1_5=PE10, EXP1_7=PE8, EXP1_9=<GND>,
+    EXP1_2=PE15, EXP1_4=PE12, EXP1_6=PE9,  EXP1_8=PE7, EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=PB14, EXP2_3=PC5,  EXP2_5=PC4,  EXP2_7=PB2,   EXP2_9=<GND>,
+    EXP2_2=PB13, EXP2_4=PF11, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<GND>
+    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi2"
+
+# See the sample-lcd.cfg file for definitions of common LCD displays.