1 files changed, 95 insertions, 0 deletions
diff --git a/config/generic-azteeg-x5-mini-v3.cfg b/config/generic-azteeg-x5-mini-v3.cfg
new file mode 100644
index 00000000..306c9a1b
--- /dev/null
+++ b/config/generic-azteeg-x5-mini-v3.cfg
@@ -0,0 +1,95 @@
+# This file contains common pin mappings for the Azteeg X5 Mini v3. To use
+# this config, the firmware should be compiled for the LPC176x.
+
+# The "make flash" command does not work on the Azteeg X5 Mini v3.
+# Instead, after running "make", copy the generated "out/klipper.bin"
+# file to a file named "firmware.bin" on an SD card and then restart
+# the Azteeg X5 Mini v3 with that SD card.
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: P2.1
+dir_pin: P0.11
+enable_pin: !P0.10
+step_distance: .0125
+endstop_pin: ^P1.24
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_y]
+step_pin: P2.2
+dir_pin: P0.20
+enable_pin: !P0.19
+step_distance: .0125
+endstop_pin: ^P1.26
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[stepper_z]
+step_pin: P2.3
+dir_pin: P0.22
+enable_pin: !P0.21
+step_distance: .0125
+endstop_pin: ^P1.28
+position_endstop: 0
+position_max: 200
+homing_speed: 50
+
+[extruder]
+step_pin: P2.0
+dir_pin: P0.5
+enable_pin: !P0.4
+step_distance: .002
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: P2.5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: P0.24
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: P2.7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: P0.23
+control: watermark
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: P0.26
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+[mcp4451 stepper_digipot1]
+i2c_address: 44
+# Scale the config so that wiper values can be specified in amps.
+scale: 2
+# wiper 0 is X (aka alpha), 1 is Y, 2 is Z, 3 is E0
+wiper_0: 1.0
+wiper_1: 1.0
+wiper_2: 1.0
+wiper_3: 1.0
+
+# Mini Viki2 LCD - this board does not work with Reprap LCDs
+#[display]
+#lcd_type: uc1701
+#cs_pin: P0.16
+#a0_pin: P2.6
+#encoder_pins: ^!P3.25, ^P3.26
+#click_pin: ^!P2.11