diff options
Diffstat (limited to 'config/example-extras.cfg')
| -rw-r--r-- | config/example-extras.cfg | 53 |
1 files changed, 53 insertions, 0 deletions
diff --git a/config/example-extras.cfg b/config/example-extras.cfg index a9a8591d..59a82c18 100644 --- a/config/example-extras.cfg +++ b/config/example-extras.cfg @@ -115,6 +115,9 @@ #samples: 1 # The number of times to probe each point. The probed z-values # will be averaged. The default is to probe 1 time. +#samples_result: average +# One can choose median or average between probes samples +# The default is average. #sample_retract_dist: 2.0 # The distance (in mm) to retract between each sample if # sampling more than once. Default is 2mm. @@ -157,6 +160,9 @@ #samples: 1 # The number of times to probe each point. The probed z-values # will be averaged. The default is to probe 1 time. +#samples_result: average +# One can choose median or average between probes samples +# The default is average. #sample_retract_dist: 2.0 # The distance (in mm) to retract between each sample if # sampling more than once. Default is 2mm. @@ -258,6 +264,47 @@ # The speed (in mm/s) when moving from a horizontal_move_z position # to a probe_height position. The default is 5. +# Tool to help adjust bed screws tilt using Z probe. One may define a +# [screws_tilt_adjust] config section to enable a SCREWS_TILT_CALCULATE +# g-code command. +#[screws_tilt_adjust] +#screw1: 100,100 +# The X,Y coordinate of the first bed leveling screw. This is a +# position to command the nozzle to that is directly above the bed +# screw (or as close as possible while still being above the bed). +# This is the base screw used in calculations. +# This parameter must be provided. +#screw1_name: front screw +# An arbitrary name for the given screw. This name is displayed when +# the helper script runs. The default is to use a name based upon +# the screw XY location. +#screw2: +#screw2_name: +#... +# Additional bed leveling screws. At least two screws must be +# defined. +#speed: 50 +# The speed (in mm/s) of non-probing moves during the calibration. +# The default is 50. +#horizontal_move_z: 5 +# The height (in mm) that the head should be commanded to move to +# just prior to starting a probe operation. The default is 5. +#samples: 1 +# The number of times to probe each point. The probed z-values +# will be averaged. The default is to probe 1 time. +#sample_retract_dist: 2.0 +# The distance (in mm) to retract between each sample if +# sampling more than once. Default is 2mm. +#samples_result: median +# One can choose median or average between screw probes +# The default is average. +#screw_thread: CW-M3 +# The type of screw used for bed level, M3, M4 or M5 and the +# direction of the knob used to level the bed, clockwise decrease +# counter-clockwise decrease. +# Accepted values: CW-M3, CCW-M3, CW-M4, CCW-M4, CW-M5, CCW-M5. +# Default value is CW-M3, most printers use an M3 screw and +# turning the knob clockwise decrease distance. # Multiple Z stepper tilt adjustment. This feature enables independent # adjustment of multiple z steppers (see stepper_z1 section below) to @@ -284,6 +331,9 @@ #samples: 1 # The number of times to probe each point. The probed z-values # will be averaged. The default is to probe 1 time. +#samples_result: average +# One can choose median or average between probes samples +# The default is average. #sample_retract_dist: 2.0 # The distance (in mm) to retract between each sample if # sampling more than once. Default is 2mm. @@ -326,6 +376,9 @@ # just prior to starting a probe operation. The default is 5 #samples: 1 # Number of probe samples per point. The defaut is 1 +#samples_result: average +# One can choose median or average between probes samples +# The default is average. #sample_retract_dist: 2.0 # Distance in mm to retract the probe between samples. Default is 2. |