diff options
| -rw-r--r-- | config/printer-anycubic-kossel-2016.cfg | 20 | ||||
| -rw-r--r-- | config/printer-anycubic-kossel-plus-2017.cfg | 15 |
2 files changed, 20 insertions, 15 deletions
diff --git a/config/printer-anycubic-kossel-2016.cfg b/config/printer-anycubic-kossel-2016.cfg index 0c4dabe0..825f6d9a 100644 --- a/config/printer-anycubic-kossel-2016.cfg +++ b/config/printer-anycubic-kossel-2016.cfg @@ -1,7 +1,9 @@ -# This file contains the configuration for the Anycubic Kossel delta -# printer from 2016. The printer uses the TriGorilla board which is an -# AVR ATmega2560 Arduino + RAMPS compatible board. To use this config, -# the firmware should be compiled for the AVR atmega2560. +# This file contains a configuration for the Anycubic Kossel delta +# printer from 2016. + +# The Anycubic delta printers use the TriGorilla board which is an +# AVR ATmega2560 Arduino + RAMPS compatible board. +# To use this config, the firmware should be compiled for the AVR atmega2560. # See the example.cfg file for a description of available parameters. @@ -12,6 +14,10 @@ enable_pin: !ar38 step_distance: .0125 endstop_pin: ^ar2 homing_speed: 60 +# The next parameter needs to be adjusted for +# your printer. You may want to start with 280 +# and meassure the distance from nozzle to bed. +# This value then needs to be added. position_endstop: 273.0 arm_length: 229.4 @@ -70,14 +76,16 @@ pin_map: arduino kinematics: delta max_velocity: 500 max_accel: 3000 -max_z_velocity: 150 +max_z_velocity: 200 delta_radius: 99.8 +# if you want to DELTA_CALIBRATE you may need that +#minimum_z_position: -5 [idle_timeout] timeout: 360 #[delta_calibrate] -#radius: 50 +#radius: 80 #manual_probe: # If true, then DELTA_CALIBRATE will perform manual probing. If # false, then a PROBE command will be run at each probe diff --git a/config/printer-anycubic-kossel-plus-2017.cfg b/config/printer-anycubic-kossel-plus-2017.cfg index 8095d59f..09db805c 100644 --- a/config/printer-anycubic-kossel-plus-2017.cfg +++ b/config/printer-anycubic-kossel-plus-2017.cfg @@ -1,14 +1,13 @@ # This file contains a configuration for the "Anycubic Kossel Linear # Plus Large Printing Size", "Anycubic Kossel Pulley Plus Large -# Printing Size" and similar delta printer from 2017. The printer uses -# the TriGorilla board which is an AVR ATmega2560 Arduino + RAMPS -# compatible board. To use this config, the firmware should be -# compiled for the AVR atmega2560. +# Printing Size" and similar delta printer from 2017. +# The Anycubic delta printers use the TriGorilla board which is an +# AVR ATmega2560 Arduino + RAMPS compatible board. +# To use this config, the firmware should be compiled for the AVR atmega2560. # See the example.cfg file for a description of available parameters. [stepper_a] -arm_length: 271.50 step_pin: ar54 dir_pin: !ar55 enable_pin: !ar38 @@ -20,7 +19,7 @@ homing_speed: 60 # and meassure the distance from nozzle to bed. # This value then needs to be added. position_endstop: 295.6 -angle: 90 +arm_length: 271.50 [stepper_b] step_pin: ar60 @@ -28,7 +27,6 @@ dir_pin: !ar61 enable_pin: !ar56 step_distance: .0125 endstop_pin: ^ar15 -angle: 210 [stepper_c] step_pin: ar46 @@ -36,7 +34,6 @@ dir_pin: !ar48 enable_pin: !ar62 step_distance: .0125 endstop_pin: ^ar19 -angle: 330 [extruder] step_pin: ar26 @@ -77,7 +74,7 @@ pin_map: arduino [printer] kinematics: delta -max_velocity: 200 +max_velocity: 500 max_accel: 3000 max_z_velocity: 200 delta_radius: 115 |