diff options
| -rw-r--r-- | config/printer-creality-ender-3-v2-2020.cfg | 88 |
1 files changed, 88 insertions, 0 deletions
diff --git a/config/printer-creality-ender-3-v2-2020.cfg b/config/printer-creality-ender-3-v2-2020.cfg new file mode 100644 index 00000000..c60bdb4f --- /dev/null +++ b/config/printer-creality-ender-3-v2-2020.cfg @@ -0,0 +1,88 @@ +# This file contains pin mappings for the stock 2020 Creality +# Ender 3 V2. To use this config, the firmware should be compiled +# for the STM32F103 with a 28KiB bootloader. To use the front USB +# port for communication, select serial port USART1. + +# If you prefer a direct serial connection, USART3 is broken out +# on the 10 pin IDC cable used for the LCD module as follows: +# 3: Tx, 4: Rx, 9: GND, 10: VCC + +# Flash this firmware by copying "out/klipper.bin" to a SD card and +# turning on the printer with the card inserted. The firmware +# filename must end in ".bin" and must not match the last filename +# that was flashed. + +# See the example.cfg file for a description of available parameters. + +[stepper_x] +step_pin: PC2 +dir_pin: PB9 +enable_pin: !PC3 +step_distance: .0125 +endstop_pin: ^PA5 +position_endstop: 0 +position_max: 235 +homing_speed: 50 + +[stepper_y] +step_pin: PB8 +dir_pin: PB7 +enable_pin: !PC3 +step_distance: .0125 +endstop_pin: ^PA6 +position_endstop: 0 +position_max: 235 +homing_speed: 50 + +[stepper_z] +step_pin: PB6 +dir_pin: !PB5 +enable_pin: !PC3 +step_distance: .0025 +endstop_pin: ^PA7 +position_endstop: 0.0 +position_max: 250 + +[extruder] +max_extrude_only_distance: 100.0 +step_pin: PB4 +dir_pin: PB3 +enable_pin: !PC3 +step_distance: 0.010752 +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PA1 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC5 +control: pid +# tuned for stock hardware with 200 degree Celsius target +pid_Kp: 21.527 +pid_Ki: 1.063 +pid_Kd: 108.982 +min_temp: 0 +max_temp: 250 + +[heater_bed] +heater_pin: PA2 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC4 +control: pid +# tuned for stock hardware with 50 degree Celsius target +pid_Kp: 54.027 +pid_Ki: 0.770 +pid_Kd: 948.182 +min_temp: 0 +max_temp: 130 + +[fan] +pin: PA0 + +[mcu] +serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 + +[printer] +kinematics: cartesian +max_velocity: 300 +max_accel: 3000 +max_z_velocity: 5 +max_z_accel: 100 |