diff options
| -rw-r--r-- | docs/G-Codes.md | 5 | ||||
| -rw-r--r-- | klippy/extruder.py | 14 | ||||
| -rw-r--r-- | klippy/toolhead.py | 2 |
3 files changed, 16 insertions, 5 deletions
diff --git a/docs/G-Codes.md b/docs/G-Codes.md index 429dff74..aa795205 100644 --- a/docs/G-Codes.md +++ b/docs/G-Codes.md @@ -84,9 +84,10 @@ The following standard commands are supported: [ACCEL_TO_DECEL=<value>] [JUNCTION_DEVIATION=<value>]`: Modify the printer's velocity limits. Note that one may only set values less than or equal to the limits specified in the config file. -- `SET_PRESSURE_ADVANCE [ADVANCE=<pressure_advance>] +- `SET_PRESSURE_ADVANCE [EXTRUDER=<config_name>] [ADVANCE=<pressure_advance>] [ADVANCE_LOOKAHEAD_TIME=<pressure_advance_lookahead_time>]`: - Set pressure advance parameters. + Set pressure advance parameters. If EXTRUDER is not specified, it + defaults to the active extruder. - `RESTART`: This will cause the host software to reload its config and perform an internal reset. This command will not clear error state from the micro-controller (see FIRMWARE_RESTART) nor will it diff --git a/klippy/extruder.py b/klippy/extruder.py index 3e4934e8..f80da6d6 100644 --- a/klippy/extruder.py +++ b/klippy/extruder.py @@ -46,9 +46,14 @@ class PrinterExtruder: 'pressure_advance_lookahead_time', 0.010, minval=0.) self.need_motor_enable = True self.extrude_pos = 0. - self.printer.lookup_object('gcode').register_command( - "SET_PRESSURE_ADVANCE", self.cmd_SET_PRESSURE_ADVANCE, - desc=self.cmd_SET_PRESSURE_ADVANCE_help) + gcode = self.printer.lookup_object('gcode') + if self.name in ('extruder', 'extruder0'): + gcode.register_mux_command("SET_PRESSURE_ADVANCE", "EXTRUDER", None, + self.cmd_default_SET_PRESSURE_ADVANCE, + desc=self.cmd_SET_PRESSURE_ADVANCE_help) + gcode.register_mux_command("SET_PRESSURE_ADVANCE", "EXTRUDER", self.name, + self.cmd_SET_PRESSURE_ADVANCE, + desc=self.cmd_SET_PRESSURE_ADVANCE_help) def get_heater(self): return self.heater def set_active(self, print_time, is_active): @@ -225,6 +230,9 @@ class PrinterExtruder: start_pos -= retract_d self.extrude_pos = start_pos cmd_SET_PRESSURE_ADVANCE_help = "Set pressure advance parameters" + def cmd_default_SET_PRESSURE_ADVANCE(self, params): + extruder = self.printer.lookup_object('toolhead').get_extruder() + extruder.cmd_SET_PRESSURE_ADVANCE(params) def cmd_SET_PRESSURE_ADVANCE(self, params): self.printer.lookup_object('toolhead').get_last_move_time() gcode = self.printer.lookup_object('gcode') diff --git a/klippy/toolhead.py b/klippy/toolhead.py index ff51c4c9..f62a86fe 100644 --- a/klippy/toolhead.py +++ b/klippy/toolhead.py @@ -372,6 +372,8 @@ class ToolHead: self.extruder = extruder self.move_queue.set_extruder(extruder) self.commanded_pos[3] = extrude_pos + def get_extruder(self): + return self.extruder # Misc commands def stats(self, eventtime): for m in self.all_mcus: |